Filter Results By:
Products
Applications
Manufacturers
Noise Sources
create signal disturbances for the purpose of noise instrument calibration.
See Also: Pink Noise, Noise Generators
- Pickering Interfaces Inc.
product
PXI Chassis And Remote Controllers
We offer both PXI & PXIe chassis and controllers that support all of our PXI switching and simulation modules as well as those from third parties. There is a choice of up to 21-slot 3U chassis with options to reduce acoustic noise and modules that can be powered from a DC source.
-
-
product
Broadband Threshold Detectors
KRYTAR's All NEW Broadband Threshold Detectors are hermetically sealed for high reliability and are specifically designed for use in today's high-performance microwave instrumentation and systems. KRYTAR detectors are designed for such applications as power measurements, analyzing radar performance, leveling pulsed signal sources, AM noise measurements, system monitoring and pulsed RF measurements in ultra-broadband and mm-Wave applications.
-
product
LED Power Driver ATS
8491
1. DC Electronic Load : Chroma 6310A/6330A Series2. Transducer Unit/Module*1 : Chroma A849101/A849102, A849103, A8491043. Time/Noise Analyzer : Chroma 80611 & 80611N card4. Sytem Controller*2 : Industrial PC5. DC Source: Chroma 62000P Series6. Digital Power Meter : Chroma 66200 Series7. OVP/Short Circuit Tester : Chroma 806128. ON/OFF Controller : Chroma 80613*1 : A849101 transfers UUT output signal to voltage signal, and measure by 84911 LED power driver measurement card (200kHz). The optional 80611N Noise card is required for 20MHz ripplecurrent measurement.*2 : The controller includes both 84911 LED Power Driver measurement card and 84903 control card.- 84911: Measure rms current, dimming current/frequency/duty, timing, power & ripple current (200kHz)- 84903 : Provide BL control signal(DC level, PWM, SM bus), and enable ON/OFF signal.C Source : Chroma 6500/61500/61600 Series
-
product
Power Sensor and SNS Noise Source Cable (1.5m / 5 feet)
11730A
The Keysight 11730 series power sensor cables are used with the 8480 and E-series power sensors (except the E9320 family of peak and average sensors). These cables are designed to reduce RFI effects on low power readings with an improved shielding design in the cable itself. Cables may be ordered individually or in pairs in any combination desired for single and dual-channel measurements.
-
product
Audio Analyzer
1121A
The Model 1121A audio analyzer provides fast, accurate measurements including frequency, AC or DC level, distortion, SINAD and signal-to-noise ratio. It also includes an audio source providing accurate low distortion signals over wide frequencies and level ranges.
-
product
Multi-Channel Vector Signal Generators
875
Berkeley Nucleonics Corporation
The Model 875 is an ultra-fast-switching vector-modulated signal source covering a continuous frequency range from 10 MHz to 40 GHz. The Model 875 offers switching speeds as fast as to 200ns, enables ultrafast CW frequency sweeps, chirping, intra-pulse modulation and pulse shaping, all with very low phase noise. A high-performance internal I/Q modulator enables customized modulation waveforms and supports dedicated modulation schemes such as avionics modulations. This newly engineered design couples extremely deep memory and wideband capabilities - making complex modulation affordable and easy to program.
-
product
Triple Output DC Power Supply, 30V/6A (2x) & 5V/3A; 375W
U8031A
Keysight now extends its range of basic DC power supplies to offer 375watt power range, making it an ideal power source alternative in electronics manufacturing, research and development as well as the education sector. The U8031A, basic DC power supply, is a manual triple-output power supply with sequencing capability. With this function, users can generate output sequences with minimal programming skills. Each power supply is also built with excellent load regulation and clean output noise for continued stability. With these and many other features, you get a solid and reliable triple-output power supply at an unsurpassed performance.
-
product
Surface-Mount Noise Sources
Mercury’s family of surface-mount noise sources provides exceptional performance in a compact and easy to integrate package. These products are ideal for applications such built-in test and dithering circuits where the system requirements drive a need for compact, surface mount technology.
-
product
Phase Noise Analyzer and VCO Tester
FSPN
The R&S®FSPN phase noise analyzer and VCO tester is designed to provide both very high sensitivity and measurement speed for production and design engineers working in these fields characterizing sources such as synthesizers, VCOs, OCXOs, and DROs. It is the ideal instrument for demanding development and production phase noise and VCO analysis.
-
product
Trace-Level UV Fluorescence SO2 Analyzer
Model T100U
Teledyne Advanced Pollution Instrumentation
The Model T100U Trace-level SO2 analyzer has been developed specifically to address the challenges of low level monitoring as required, for example, in the US NCore network. It uses the proven UV fluorescence principle, and is designed to allow ultra-sensitive SO2 measurements while still meeting the requirements for use as a US EPA compliance analyzer.The analyzer uses both the light and dark phases of the pulsed UV light source to continuously detect and correct for electronic noise, giving exceptionally stable and sensitive performance. A separate UV detector allows the instrument to continuously correct for variations in lamp intensity. Exceptional stability is achieved with the use of an optical shutter to compensate for PMT drift, and a reference detector to correct for changes in UV lamp intensity. A hydrocarbon "kicker" and advanced optical design combine to prevent inaccuracies due to interferents.
-
product
Phase Noise Measurement Solution, 50 kHz to 110 GHz
E5505A
The Keysight Technologies E5500 Series of phase noise measurement solutions offers the most flexible set of measurements on one-port VCOs, DROs, crystal oscillators and synthesizers. Two-port devices, including amplifiers and converters, plus CW, pulsed and spurious signals can also be measured. The E5500 measurements include absolute and residual phase noises, AM noise, and low-level spurious signals. The stand-alone instrument architecture easily configures for various measurement techniques, including the PLL/reference source technique, residual and FM discriminator methods.
-
product
RF Synthesizers Modules
Holzworth Instrumentation, Inc.
Holzworth's RF Synthesizers Modules were originally designed as the internal, tunable LO test sources for Holzworth phase noise analyzer products. Due to the need for easy integration, the HSM Series designs incorporate a long list of electrical and mechanical features to satisfy the demanding requirements of today's high performance communications systems and integrated test systems. FIELD PROVEN RELIABLITY with MTBFs exceeding 240kHrs.
-
product
Microwave Wideband Externally Modulated Transmitters (without RF Amp)
MT80 (30KHz~40GHz)
Hangzhou Huatai Optic Tech. Co., Ltd.
MT80 series microwave optical transmitter, adopts external modulation technique, are able to transmit 40GHz microwave RF signal with long distance, wide bandwidth, and flat responsibility. They provide an outstanding linearity fiber optical communication for analogue and digital wideband microwave application. Due to avoidance of using expensive coaxial cable or wave guide, there will be no limitation in transmission distance, which improves the signal quality and reliability of the microwave communication. They can be widely applied in microwave communication system such as remote wireless; timing and reference signal distribution, telemetry, measurement and delay line etc as well as 10Gb/s and 40Gb/s high speed communication system. MT80 adopts low noise, narrow linewidth CW DFB laser as light source; LiNbO3 external modulator as signal modulation, no laser chirp, low dispersion distortion, high extinction ratio, Full-transparency operation mode. It can be applied in long distance and extra-long distance transmission after EDFA.
-
product
Microwave / RF Synthesizers, Test & Measurement
Berkeley Nucleonics Corporation
The 825-M is an agile ultra-low phase noise RF signal source from 8 kHz to 20 GHz RF Synthesizer. It is available in single-channel or multichannel configurations. A single channel 825-M is packaged in a compact enclosure, or can be ordered with a touch-screen display, or a 1U 19" rackmountable version. The multi-channel version (2, 3, or 4 channels) is packaged in a 19” 1U rackmount enclosure.
-
-
product
VECTOR-GUN HANDHELD DIRECTION FINDING ANTENNA SYSTEM
HFDF
National RF's Type HFDF active directional antenna system consists of a high gain RF amplifier coupled to a tunable Faraday shielded loop antenna. Several loop antenna assemblies are available to provide coverage of frequencies in the HF and low VHF spectrum. Due to the nature of a Faraday shielded loop, the antenna exhibits a sharp null through the diametric center of the loop. This null is used to determine the direction of incoming radio signals or to locate electrical noise being radiated from some source. The internal high gain amplifier is used to compensate for the inherent inefficiency of the actual loop at the operating frequency. Overall, the system dynamic response is about +6 dB as compared to the dynamic response of a dipole. To aid in the direction finding process on strong signals, an internal 30 DB attenuator is provided. As the loop antenna presents a bi-directional response, tri-angulation may be required to eliminate the ambiguous signal direction. The line of site of the incoming signal is determined by listening for a signal null on the receiver or by watching the receiver’s S-meter.
-
product
Phase Noise Analyzer and VCO Tester
FSWP
The R&S®FSWP phase noise analyzer and VCO tester features very high sensitivity thanks to extremely low-noise internal sources and cross-correlation. It can measure phase noise and amplitude noise in mere seconds on highly stable sources such as those in radar applications. Additional options such as pulsed signal measurements, residual phase noise (including pulsed) characterization and integrated high‑end signal and spectrum analysis make the R&S®FSWP a unique test instrument.
-
product
Phase Noise Testers / Signal Source Analyzers
7000 Series
Berkeley Nucleonics Corporation
The 7000 series is an all-in-one integrated solution that offers an indispensable set of low-noise phase measurement functions. Offering both Absolute and Additive(residual) measurement capabilities in one unit at no additional cost, the 7000 series is the most flexible solution on the market. The instrument comprises a two-channel, cross-correlation system with two internal, tunable references sources that also allows measurements with externally sourced references. We offer three platform options for the 7000 Series Phase Noise Testers: the 7070 1 MHz to 7 GHz, the 7300 1 MHz to 26 GHz, 7340 1 MHz to 40 GHz, 7350 1 MHz to 50 GHz, and the 7360 1 MHz to 65 GHz.
-
product
Low Noise Pre-Amplifiers
Low Noise Pre-Amplifier and companion external low noise amplifier (LNA) are used to amplify low level microwave signals. The Pre-Amplifier contains an AC/DC power supply, internal low noise amplifier, and a bias tee to source a DC bias voltage on the RF input connector.To overcome cable loss between the test antenna and the Pre-Amplifier assembly, a remote low noise amplifier (LNA) is mounted directly onto the 10 GHz antenna. A bias tee inside the Pre-Amplifier chassis powers the remote LNA through the coax cable interconnecting the pre-amplifier and the 10 GHz test antenna.
-
product
Signal Generators
SSG5000X Series
SIGLENT’S SSG5000X series of signal generators can generate analog and vector signals, and have a frequency range of 9 kHz to 4 GHz/6 GHz. They feature the industry-leading performance in phase noise, spectral purity, bandwidth, EVM, output power. The internal IQ modulation generator and waveform playback function make it easy to create even the most complex signal types. They also cover the most important RF band for digital wireless communications and include standard waveform files. The SIGLENT SSG5000X are powerful and cost effective sources that are ideal for R&D, education, and manufacturing.
-
product
Measurement Hardware
Whether it’s in a vehicle, on a test stand or monitoring equipment and machinery - imc data acquisition systems are easy to operate and will help you become more productive and profitable. Our products are suited for work in mechanical and mechatronic applications. They handle up to 100 kHz per channel, are compatible with almost all signal sources and sensors, and can measure nearly all physical quantities such as pressure, force, speed, vibration, noise, temperature, voltage and current. The spectrum of imc data acquisition systems ranges from simple data acquisition via integrated real-time calculations, to the integration of models and complete automation of test stands.
-
product
Audio Analyzers
Audio analyzer provides fast, accurate measurements including frequency, AC or DC level, distortion, SINAD and signal-to-noise ratio. It also includes an audio source providing accurate low distortion signals over wide frequencies and level ranges.
-
product
60 GHz Noise Figure Test Set
The Noisecom 60 GHz Noise Figure test set has 4 separate systems designed to perform Y-factor noise figure measurements using a high performance Spectrum Analyzer or a dedicated receiver. Each system contains a highly stable V-band noise source, isolator(s), optional waveguide to coaxial transitions and an optional pre-amplifier for use with a spectrum analyzer. The two standard calibration tables have ENR data points at 1 GHz intervals.* System ENR is measured before the DUT connector and at the final output stage allowing for pre-test calibration of the system.
-
product
Precision Calibrated Noise Sources
ELVA-1's calibrated noise source ISSN-XX series delivers a uniform level of noise power spectral density within the whole waveguide frequency range. Sources are available in eight waveguide bands covering 26.4-170 GHz.
-
-
product
High-Density Precision SMU (10 PA, 30 V)
PZ2131A
The Keysight PZ2131A is a high-channel density precision source / measure unit (SMU) having 5 channels per module and saving space for a wide range of applications requiring numerous precision power supplies. The narrow-pulse function and fast Digitizer Mode allow the PZ2131A to expand the conventional static DC measurements to emerging dynamic measurements. Its seamless current measurement ranging function eliminates the time it takes to change the range and expands the dynamic range to cover multiple measurement ranges, which reduces test duration. These capabilities make the PZ2131A suitable for applications that require numerous precision power supplies, such as semiconductor reliability tests and integrated circuit (IC) tests. The Keysight PX0107A low noise filter adapter lowers its voltage source noise level, which makes the PZ2131A suitable for noise-sensitive applications such as quantum computing as well.
-
product
Power Line Meter
The Line EMI Meter measures electromagnetic interference in a single-phase AC power line. It plugs into a wall outlet (mains socket) and requires no battery. It immediately displays total line noise in millivolts (range 1999 mV, resolution 1 mV) in the frequency range 10 KHz 10 MHz (the frequency limits at which sensitivity is of the maximum sensitivity). A speaker plays the sound of the EMI, amplitude demodulated, in order to identify the EMI source (such as an AM or shortwave radio station vs. a motor vs. an electric arc).
-
product
Noise Test
Noise testing is conducted to determine if materials can withstand external noises generated by various sources. It also includes air-borne and structure-borne noise measurements.
-
product
Low Phase Noise Reference Source
96270A
The 96270A RF Reference Source is the simplest, most accurate and cost-effective single instrument for calibrating spectrum analyzers and RF power sensors and more, up to 27 GHz.
-
product
Noise Source, 10 MHz to 18 GHz, nominal ENR 6 dB
346A
The Keysight 346A noise source is the ideal companion to Keysight's noise figure solutions. Since it is broadband (10 MHz to 18 GHz), it eliminates the necessity for several sources at different frequency bands. The low SWR of the noise source reduces a major source of measurement uncertainty; reflections of test signals. The very small change in reflection coefficient (<0.01) from ON to OFF is designed especially for accurate characterization of input-impedance-sensitive devices (like GaAsFETs and many UHF amplifiers).
