Filter Results By:
Products
Applications
Manufacturers
Noise Figure
delta of UUT noise to ideal.
- Applied Instruments, Inc.
product
Forward Path NPRT 2200 Noise Power Ratio Test Set
NPRT 2200-F
The NPRT 2200 measures the NPR of a device across a range of power levels. This test quantifies intermodulation distortion and determines the dynamic range of optical transmitters, amplifiers and other active HFC network devices. The included PC software uses predefined test setups to run a "Power Sweep" series of NPR measurements and graph the results.
-
product
Receiving Amplifiers
he products from Kuhne electronic from the category "Receiving Amplifiers for Professional Use" are designed for the following applications: Radio Link Systems, Satellite Receivers as well as Scientific and Measurement Instrumentation.These amplifiers stand out due to outstanding Noise Figures as well as a very good Large Signal Stability and small Housing Sizes.
-
product
PXI Network Analyzers
M980xA Series
The Keysight M980xA Series of PXI network analyzers meets the most demanding challenges with a true multiport architecture that offers exceptional performance no matter how many ports you use. Gain deeper insights into your devices with the widest available portfolio of measurement applications for PXI VNAs, including spectrum analysis and noise figure measurements.
-
product
Frequency Block Converter
FBC
The FBC-XX-FB is a full band system can be built upon a Keysight N8975A Noise Figure Analyzer (NFA) or X Series Signal Analyzer with option N9069A. This system allows the user to extend the frequency range of the NFA to allow for accurate noise figure measurements to be performed on a device covering Ka, U, V, E, W bands (26.5-170 GHz), when used with an Agilent E8247C signal generator (or equivalent).
-
product
RF/Microwave Test Capability
Teledyne Labtech have extensive microwave alignment and microwave testing facilities. This includes the ability to test noise figure, S-parameters and harmonics. This ensures that Teledyne Labtech can supply a fully compliant product and provide a complete turnkey microwave assembly and test solution.
-
product
Low Noise Amplifier (DC Powered)
Low noise amplifiers offering low noise figure and high linearity
-
product
PCI Express A/d Board
AD14-500x4-8GB-K7US
The AD14-500x4-8GB-K7US is a high performance wideband 4-channel 14-bit data single PCIe Gen3 board, that can continuously digitize four wideband signals, with four high linearity A/Ds.Designed for demanding military, medical, scientific, industrial, communications, safety and electrical power utility applications, these boards have a wideband noise figure of 10dB and 1 dB peak-to-peak ripple over the DC to 250MHz frequency spectrum (2dB p-p over DC-500MHz).
-
product
Automated Tuners / Impedance Tuners / Load Pull Tuners
MT97x, MT98x and XT98x series automated tuners (also known as automated impedance tuners and automated load pull tuners) are precision instruments that are optimized for a broad class of in-fixture and on-wafer applications, and may be used in any automated or manual application requiring the ability to match the impedance of a microwave circuit element or to establish specific impedances at a terminal interface. The tuner design is based on the slide screw concept using the inherently broadband slab-line transmission structure. Each unit has two non-contacting probes deliver high VSWR with superb accuracy and reliability over a wide frequency range. These probes can be fully retracted leaving a low-loss, well-matched transmission line, which is a significant benefit in power related applications where two-port tuners capable of handling large amounts of power are required. As integral components of Maury Device Characterization Solutions, these PC-based tuners are controlled using Maury's family of Device Characterization Software tools, including MT930 IVCAD, MT993 ATS and the DLL-based measurement automation environment. Maury Microwave automed impedance tuners are ideal for load pull, harmonic load pull, active load pull, hybrid active load pull, noise figure, noise parameters and all automated tuner applications.
-
product
V-Band Low Noise Amplifier 50 to 75 GHz, 35 dB Gain, 5 dB NF
SBL- 5037533550-1515-E1
50 to 75 GHz, 35 dB Gain, 5 dB Noise Figure V Band Low Noise Amplifier for IEEE 802.11.ad WiGig. Model SBL-5037533550-1515-E1 is a low noise amplifier with a typical small signal gain of 35 dB and a nominal noise figure of 5 dB across the frequency range of 50 to 75 GHz. The DC power requirement for the amplifier is +8 VDC/150 mA. The mechanical configuration offers an in-line structure with WR-15 waveguides and UG-385/U flanges.
-
product
RF/Microwave Test Capability
Teledyne Labtech have extensive microwave alignment and microwave testing facilities. This includes the ability to test noise figure, S-parameters and harmonics. This ensures that Teledyne Labtech can supply a fully compliant product and provide a complete turnkey microwave assembly and test solution.
-
product
5G Switch LNA Modules
Macom Technology Solutions Holdings Inc.
MACOM offers a complete portfolio of high-power switch and LNA modules to cover many sizes and classes of 5G base stations, including Macro Cell, Small Cell, and massive-MIMO AAS in frequency bands up to 6GHz. SOI-based switch modules with up to 20W LTE power handling are extensively used in mMIMO and Small Cell radios, and MACOM proprietary PIN diode Switch modules with up to 160W LTE power handling are widely deployed in Macro radios. Featuring ultra-broadband, low noise figure and excellent power handling and reliability, the family of Switch LNA modules are also well suited for a variety of TDD based communication systems in commercial and military applications.
-
product
C-Band Separate Raman Fiber Amplifier
RFA5000
Hangzhou Huatai Optic Tech. Co., Ltd.
1. Erbium-doped Fiber Amplifier, due to the multiple cascades and the accumulation of noise caused by spontaneous emission, will reduce the system CNR greatly and thus it will limit the transmission capacity and distance of the system. Raman Fiber Amplifier (RFA) is a newly designed fiber amplifier based on Stimulated Raman Scattering (SRS) effect. It is considered as the core technology of new generation DWDM fiber over-long communication. Compared with Erbium-Doped Fiber Amplifier, Raman amplifier has the advantage of low Noise Figure (NF), wider gain bandwidth, flexible gain spectral region and stable temperature. It is the only device that can operate in 1300~1600 nm.
-
product
60 GHz Noise Figure Test Set
The Noisecom 60 GHz Noise Figure test set has 4 separate systems designed to perform Y-factor noise figure measurements using a high performance Spectrum Analyzer or a dedicated receiver. Each system contains a highly stable V-band noise source, isolator(s), optional waveguide to coaxial transitions and an optional pre-amplifier for use with a spectrum analyzer. The two standard calibration tables have ENR data points at 1 GHz intervals.* System ENR is measured before the DUT connector and at the final output stage allowing for pre-test calibration of the system.
-
product
Low Phase Noise Amplifiers
Pasternack's low phase noise amplifiers cover select frequency bands ranging from 1.5 to 18 GHz with residual phase noise levels as low as -180 dBc/Hz @ 10 KHz offset. Additional performance specs include small signal gain ranging from 9 to 14 dB, with typical noise figure of 5.5 dB. Psat levels for these amplifiers range from +16 to +25 dBm with Output IP3 levels as high as +34 dBm. All models feature single DC voltage supplies and input/output RF ports are internally matched for 50 ohms with DC blocking capacitors. These compact module assemblies require no external components and are available in rugged Kovar metal drop-in packages that are gold-over-nickel-plated and support field replaceable SMA connectors. All models are EAR99 and guaranteed to meet MIL-STD-883 test conditions for hermeticity and temperature cycle.
-
product
Gain Blocks
Analog Devices RF amplifiers are designed utilizing the company’s leading amplifier and RF IC expertise. Our extensive family of single-ended input/output, fixed-gain amplifiers can be used from dc to microwave and include gain blocks, low noise amplifiers, intermediate frequency amplifiers, driver amplifiers, and differential amplifiers. These devices offer high linearity, low noise figures, and various fixed-gain options, as well as low power consumption; they are all fully specified over frequency, temperature, and supply voltage for use in a variety of applications.
-
product
Ku Band Gain Control Amplifier
Expanding Teledyne RF & Microwave's existing line of high frequency amplifiers, microwave gain controllable amplifiers are designed and biased for critical performance applications. One example covers 10-13 GHz, offers 45 dB unattenuated small signal gain with 15 dB attenuation range. Typical gain flatness is ±0.5 dB, +35 dBm third order intercept point, +22 dBm minimum 1-dB gain compression, and 3.5 dB unattenuated noise figure 4.5 dB at full attenuation. This is only one of a series of microwave controllable amplifiers currently in production.
-
product
Noise Source, 10 MHz to 18 GHz, nominal ENR 6 dB
346A
The Keysight 346A noise source is the ideal companion to Keysight's noise figure solutions. Since it is broadband (10 MHz to 18 GHz), it eliminates the necessity for several sources at different frequency bands. The low SWR of the noise source reduces a major source of measurement uncertainty; reflections of test signals. The very small change in reflection coefficient (<0.01) from ON to OFF is designed especially for accurate characterization of input-impedance-sensitive devices (like GaAsFETs and many UHF amplifiers).
-
product
Radar Target Repeater
Series 8000
The Eastern OptX Series 8000 Radar Target Repeater is a portable, variable delay and propagation loss system designed for radar testing and alignment. The repeater may be remotely programmed in the field for dynamic operation. When connected to a user specified antenna the repeater can provide delays of up to 500 usec with a fixed delay, multiple discrete delays, or a progressive variable delay with amplitude control The Series 8000 features ultra wide bandwidth, low loss, high isolation, low noise figure, and high dynamic range.
-
product
VDI Millimeter-Wave Frequency Extension Modules for PXA, MXA, EXA Signal Analyzers
These modules offer low conversion loss and excellent noise figure. Standard features include dual operating modes. First, the module can function as a high performance down-converting mixer. The second operating mode functions as a block down-converter with a broadband IF up to 20 GHz. Power to the module is provided via an included external DC power supply. These frequency extenders minimize conversion loss by multiplying and amplifying the LO signal internally, thus taking advantage of the benefits of low harmonic mixing. This architecture also preserves the X-Series precision frequency resolution and low phase noise, extending those qualities into the millimeter and sub-millimeter bands.
-
product
Downconverter for the 21cm Bandvalon
2100
1440MHz inputLow noise figure LNA 0.3dB 20 KHigh gain >40dB8-pole ceramic dielectric input filterHigh dynamic range, low-spurious responses Rugged milled aluminum housingRFI shielded constructionDesigned for use with Valon 5009 as LOSuitable for hydrogen line observation and general radio astronomy in the 21cm band.6Vdc @ 400mAIncludes 20” dc power supply cable
-
product
Noise Source, 1 GHz up to 50 GHz
346CK01
The Keysight 346CK01 is the ideal companion to Keysight´s noise figure solutions when working on high frequency applications. Since it is broadband (1 GHz to 50 GHz), it eliminates the necessity for several sources at different frequency bands. The low SWR of the noise source reduces a major source of measurement uncertainty, which are reflections of the test signals. This is a coaxial noise source with a 2.4 mm coaxial connector. ENR typically 20 dB at 1 GHz, decreasing to typically 7 dB at 50 GHz.
-
product
Receivers
Macom Technology Solutions Holdings Inc.
MACOM's receivers are widely used in point-to-point radio, aerospace and defense, and other broadband communications applications. Operating between the 4.5 - 45 GHz frequency range, our receivers feature an integrated LNA, mixer and LO buffer amplifier onto a single chip. Available in lead-free QFN or SMD packages, our receivers boast excellent noise figure and conversion gain performance.
-
product
Super Low Noise Amplifiers
WCA Series
WCA series super low noise amplifiers have sub-0.5 dB noise figure at VHF band with several octave bandwidth. The amplifiers have 75 Ohm impedance.
-
product
Noise Figure Measurements With Vector Correction
S93029B
The S93029B noise figure application enables high-accuracy noise figure and noise-power measurements of amplifiers, frequency converters, and mixers, utilizing Keysight’s unique vector-source-correction technique
-
product
LNA, Millimeter-wave Power Amplifier And Rack Mount Amplifier
Panda Microwave design up to 50GHz broadband power amplifier, including LNA, CW and pulse medium, Rack Mount Amplifier and millimeter-wave high power amplifier. Our amplifiers cover frequency range from 100MHz to 50GHz and use Thin-film Technology. Low noise amplifier have superior noise figure numbers and a variety of models. Gain block low noise amplifiers provide all around gain where noise is not critical. High power amplifier system equipment is available with either manual or digital control interfaces, power capacities up to 100W pulse power.
-
product
Low Noise Amplifiers
WA Series
WA series low noise amplifiers are the balance type LNA with alarm capability in some of the products. Besides offering very low noise figure and wide bandwidth, the LNA have high linearity with unconditional stable design. The noise figures are from 0.40 dB to 1.0 dB and IP3 from 30 dBm to 40 dBm.The amplifiers cover the frequency bands of VHF, UHF, Cellular, GSM, DCS, PCS, 3G, C, and wireless LAN. The built-in alarm capabilities include Branch 1 and Branch 2 alarms, Soft Failure alarm, Hard Failure alarm, Soft alarm Open-Collector, and Hard alarm Open-Collector.
-
product
Preamplifiers
LNA Series
Low noise amplifier with 12.5 dB of gain covering the nominal frequency range 1 MHz to 3 GHz and can be used in the range from 200 kHz to 4 GHz. With its high gain and low noise figure, it will significantly increase the sensitivity of virtually all spectrum analyzers and other RF measuring instruments. All measuring instruments have a 'noise figure', which is a measure of how good the instrument is at measuring low level signals, the lower this figure, the better, although the lowest signal level will still be governed by the measurement bandwidth. A typical spectrum analyzer may have a noise figure of 20 dB or more, whereas a typical receiver may have a noise figure of 10 dB. The preamplifier has a noise figure of typically 4 dB, significantly enhancing the low level performance of such instruments, enabling signals that were previously masked by noise to be seen.
-
product
Resistance Tester
KT-2000RD
This equipment represents the wanted resistance value in digital figures and at the same time, is an ohmmeter which decides products to be bad in case of being out of the previously set range of H,L and to be good in case of being within the range. Moreover, because it is designed and manufactured on the basis of KAST's business experiences and know-hows accumulated through on-the-spot works for a long time, it is highly trustable, especially strong to noise and impulse that occur on the bad electric condition of on-the-spot or on the connection with any other equipments, and also is convenient for use.
-
product
K-Band Silicon SATCOM Rx Quad Core IC
AWS-0102
The AWS-0102 is a highly integrated silicon quad core IC intended for satellite communications applications. The device supports four dual polarization radiating elements with full programmable polarization flexibility. The device provides 22 dB of gain with a noise figure of 3.4 dB. Additional features include gain compensation over temperature and temperature reporting. The chip features ESD protection on all pins, operates from a +1.8 V supply, and is packaged in a 56 lead 7x7 mm QFN for easy installation in planar phased array antennas.
-
product
Real-Time Spectrum Analyzers (RTSA)
Gain more confidence in your system or signal environment knowing you can capture intermittent or transient signals as short as 3.57 µsMaximize your investment when you add real-time capabilities to a UXA, PXA or MXA X-Series analyzer -no need for a dedicated instrumentGo deeper and thoroughly analyze complex signals with the 89600 VSA softwareAccelerate communication system development by quickly switching to must-have traditional measurements like phase noise, noise figure, and more
-
product
Medium-Power, Broadband Amplifiers
Our family of distributed amplifiers utilize advanced broadband design techniques to achieve solid performance in gain, flatness, noise figure and output power over a wide frequency range. The experienced design team has the know-how and tools available to take any standard product and customize it for your specific application.
