Filter Results By:
Products
Applications
Manufacturers
- Pickering Interfaces Inc.
product
PXI/PXIe Battery Simulator Module, 2-Channel, V/I Readback, Simplified Current Sink, 750 V Isolation
41-752A-913
Targeting EV, automotive, aerospace, energy storage and electric aircraft applications, the new battery simulator modules occupy a single PXI slot. These 2-channel battery simulators are capable of supplying up to 7 V and 300 mA per channel. The channels are fully isolated from ground and from each other, allowing series connection to simulate batteries in a stacked architecture.
-
product
Lead Acid Intelligent Battery Tester
612
This digital battery tester is designed for testing 6V and 12V standby SLA, cyclic GEL and car FLOODED batteries. Simple in operation, the ACT 612 simulates a full 20 hour (C20) discharge test in seconds and displays the DC Voltage results and Ah capacity available.
-
product
Battery Tester
Changzhou Applent Instruments Inc.
Is an electronic device intended for testing the state of an electric battery, going from a simple device for testing the charge actually present in the cells and/or its voltage output, to a more comprehensive testing of the battery's condition, namely its capacity for accumulating charge and any possible flaws affecting the battery's performance and security.
-
product
Battery Voltage Supervisor
BVS
DV Power battery voltage supervisor – BVS, is an accurate battery voltage monitoring system that monitors the state of health of battery systems. It records important battery parameters such as battery voltage, inter-cell connection voltage, and ambient temperature. Because of that, it can be a support tool for capacity testing.The BVS voltage supervisor is an integrated system consisting of:BVS Control Unit (BVS-CU)Cell Voltage Modules (CVM)String Voltage Module (SVM) (optional)String Current Module (SCM) (optional)It is an ideal testing tool for maintenance, troubleshooting and performance tests on individual stationary batteries and battery packs in critical backup energy solutions.BVS-CU provides ambient temperature measurements on multiple locations (4 temperature channels). Overall string voltage and string current monitoring can be achieved by using an optional string voltage module (SVM) and string current module (SCM).There are two types of DV Power battery voltage supervisors:BVS – One cell voltage module measures 1 cellBVS-4 – One cell voltage module measures 4 cellsCVM modules detect cells that fail a discharge test based on monitored voltage values. As a result of that, these cells can be safely removed from the battery string.Data acquisition and analysis of data collected from the modules are available in the DV-B Win application software suite. They provide data viewing, tracking, and generation of comprehensive reports.
-
product
Battery Discharge Capacity Tester
KV Hipot Power Test Equipment Co.,Ltd
Battery Discharge Capacity Tester is used to perform discharge testing which is the verifiable method to determine actual capacity of battery systems.
-
product
Battery Analyzer with Capacity Range 200.00Ah
SE-1005
● Battery ImpedanceRange: 60mΩ / 600mΩ / 6 Ω / 60Ω (auto-range)Accuracy: ±1.0% of reading ±3digits Resolution: 0.01mΩ● DCV Range: 6V / 60V (auto-range) Accuracy: ±0.8% of reading ±3digits Resolution: 0.001V● DCARange: 60AAccuracy: ±1.0% of reading ±3digits Resolution: 0.01A● CapacityRange: 999.99AhAccuracy: ±1.5% of reading ±3digits Resolution: 0.01AhDischarge load:8Ω/1.5Ω
-
product
Full-Featured Life Cycle Test System
LCV
Configurations for testing to industry standards: IEC, SAE, BCILife Cycle Testing: Perform charge/discharge cycling of batteries or modules to obtain charge and discharge capacity, energy and DC internal resistanceAutomotive Battery TestingStarting, Lighting and Ignition (SLI) TestingTraction Battery Testing
-
product
Battery Electronics
CAES Battery Electronics provide autonomous, dissipative, and continuous cell balancing to maximize available battery capacity, and therefore battery cycle life, throughout a mission.
-
product
Battery Discharge and Capacity Testers
HD Power Test Equipment Co.ltd
HDFD Battery Discharge Tester can be used as the discharge load in the battery off-line state to realize the constant discharge at the set value by regulating continuously the discharge current. When discharging, the tester will automatically stop discharging when the voltage on the battery group terminal or the cell falls to the set lower limit value, or when the set discharging time is out, or when it reaches the set discharging capacity. Battery Discharge Tester can records all valuable and continuous real-time data during the discharge process.This tester system is simple, safe and accurate for monitoring voltage of cells adopting wireless connection.
-
product
LiFePO4 UPS (Lithium Iron Phosphate Battery) – 1.5kVA to 3kVA
SSG Industrial Series
*Very lightweight – 44% less. Each Falcon LiFePO4 battery pack weighs 44% less than a lead-acid equivalent. This is ideal for applications with a weight/footprint requirement.*3 to 4 times longer runtimes. The high-energy battery capacity means fewer battery packs and longer runtimes.*Long service life: 10-years plusWith 4 times more charge/discharge cycles, you cut battery replacements and service costs.*-20°C to 55°C temperature range. Tolerance of wide temperatures makes the SSG Industrial LiFePO4 UPS ideal for demanding environments.*Advanced safety. Lithium iron cathode material has no thermal runaway issues. The LiFePO4 battery is safe for the environment. It has no caustic materials or dangerous odors.*Falcon is recognized for quality and reliability. Falcon Electric is a recognized authority in industrial UPS solutions. Our technical expertise assures you find the right solution–the first time.
-
product
Mini Multi-Battery Tester
Mini-MBT
The ZTS Mini Multi-Battery Tester (Mini-MBT) provides a comprehensive means of testing the state of charge or state of power for more than 15 battery types. The mini-MBT’s microprocessor-based design makes battery testing simple - using a patented, high accuracy pulse load test. After a fully automatic test cycle, percentage of remaining battery capacity is indicated on the LED bar display.
-
product
Battery Discharger & Capacity Tester
IDCE-8X0
Fuzhou Fuguang Electronics Co., Ltd.
Wide Range: IDCE-8X0CT series can cover 10V~480V for multiple batteries test requirements like telecom (48VDC), powerutilities (110VDC, 220VDC), UPSs (300-60 VDC), traction batteries(12-96VDC)etc.
-
product
Battery Analyzer with Capacity & Impedance Measurement
SE-1005A
Range: 60mΩ / 600mΩ / 6 Ω / 60Ω (auto-range)Accuracy: ±1.0% of reading ±3digits Resolution: 0.01mΩDCV Range: 6V / 60V (auto-range) Accuracy: ±0.8% of reading ±3digits Resolution: 0.001VDCARange: 60AAccuracy: ±1.0% of reading ±3digits Resolution: 0.01ACapacityRange: 999.99AhAccuracy: ±1.5% of reading ±3digits Resolution: 0.01AhDischarge load:24Ω;
-
product
Battery Fuel Gauge
Global Digital Instruments, LLC
SenDEC Battery Fuel Gauges are designed to accurately monitor the charge capacity of lead acid batteries. SenDEC fuel gauges can be used to monitor DC powered equipment such as fork lifts, golf carts, floor care equipment, and any other battery powered equipment. Three battery discharge profiles are standard, plus custom profiles, and a lockout option.
-
product
6/12/24/36V Conductance Battery Tester
MBT300
Tests 6/12/24V lead acid batteries individually or in parallel and series battery packs. Displays battery or battery pack condition as % available capacity, rated capacity (CCAs), state of charge voltage, and good or replace status. Tests 6/12/24/36V starter and charging systems including starter draw, alternator and regulator output (loaded/unloaded), and diode ripple.
-
product
Circuit Breaker Contact Resistance Meters
Vanguard Instruments Company, Inc.
The Vanguard Auto-Ohm 10 is a 10-ampere battery powered micro-ohmmeter designed for low-resistance-measuring applications such as the measurement of resistance in circuit breaker contacts, bushing contact joints, and welding joints. The unit is powered by four 3400mAh, 3.7Vdc Li-Ion rechargeable batteries. With these high capacity batteries, up to 2,900 tests per charge (10A/2 second duration) can be performed in the field.
-
product
Test Solutions
AT/CX/CM Series
The VeEX AT/CX/CM series are next generation test solutions designed for analog and digital cable TV networks supporting VoIP, WiFi, and Internet service. Analog and Digital SLM, ingress noise sweep, deep interleave support, and QAM constellation analysis are among many standard features. Enhanced optional features include QAM16/64/128 Upstream Generation (USG), Reverse Path QAM Analysis, and DOCSIS 2.0/DOCSIS 3.0 Cable Modem emulation. A high capacity LiIon battery pack provides extended autonomy for a full day use with only a single charge.
-
product
Test Device for Bicycle Batteries
ATGF 1500/PBG
The ATGF 1500 is a multifunctional testing instrument for bicycle batteries and accompanying battery chargers. The easy to use ATGF 1500 is suitable for battery systems of Derby Cycle, Gazelle, Simplon and ZEG. est programs: Quick Test, Capacity Test, Recalibration.
-
product
Battery Testing
BTS 200
This testing and maintaining battery system allows to perform measurement of battery voltage, discharging current test and testing of battery capacity. BTS 200 can be connected with external load unit ELU 200.
-
product
SOC Battery Tester
This sophisticated battery test equipment allows the battery tester to exercise and explore the battery’s internal profile and produce a true state of charge revealing the batteries true AHR capacity and ability to perform under load.
-
product
NetXpert XG2 High Cap Battery Kit
#TXGBATX
*Easy installation*Increases battery capacity by 50%
-
product
20KVA to 200KVA Industrial UPS (3Ø – 3Ø)
NSP Series 20KVA to 200KVA
- Designed for powering critical Industrial and IT systems- DSP controlled IGBT based PWM technology- Design topology enables N+1 parallel redundancy- Industrial grade high speed CAN bus communication- User Friendly Matrix LCD and LED mimic front control and digital monitoring- Fully rated make before break maintenance bypass operation- Optional break-less load transfer via static switch- Low harmonic distortion- High crest factor tolerance and dynamic stability- Lower TCO- Continuous full rated power at ambient as high as 45°C- N+1 Parallel operation of UPS without any common hardware- Advanced Communication Capability (RS485/Modbus/SNMP)- High branch fuse clearing capacity- On-line battery bank test without load disconnection- Compact, elegant, and light weight enclosure- Easy installation with wheels for maneuverability and front bottom terminals
-
product
Battery Analyzer
KT-99/99A
Measure battery storage capacity with clamp-on sensorTest battery capacity under it’s real working conditionSelect different type of battery with discharge end voltageDisplay current and voltage during testingDisplay battery parameters and timeAuto-alarm when test finish,alternatively data savingAuto backlight on in dark areaMaximal capacity count up to 999.9Ah4-wires mode impedance measurement Up to 0.01mΩ resolutionOperating Environment: 0～40℃ ,<80% R.HStorage Environment : -20～60℃ ,<80% R.HPower supply: Heavy duty 9V Alkaline battery ( IEC-6F22)Accessories: “4 wire” test leads 1 pair “2 wire” test leads 1 pair
-
product
Multifunctional Electrical Installation Parameter Meter
AMPI-540
Much more than a multi-function meter*the largest 7" touch panel on the market - outstanding ergonomics and ease of use*removable microSD card - easy increase of memory capacity*lithium-ion battery - longer meter operation*possibility to add a voice memo or a photo to the measurement - multimedia description of the measurement site*
-
product
Battery Testers
Battery testers are electronic devices designed to test the remaining capacity of a battery's overall charge.
-
product
Vehicle-Mounted Radar
Stalker II
• Very high performance design using DSP technology• Faster speed tracking • 3 window display • Track-thru lock • Backlit LCD for nighttime use • Advanced digital signal processing (DSP)• New high capacity battery handle• Cordless operation available • Remote control option • Detachable handle design • Touch panel keyboard • Rugged die-cast metal construction • Moving & stationary versions • 2-Year full warranty
-
product
Panel Meters
Wuxi IMHOO Technology Co., Ltd.
1. Residual capacity of battery(Ah or mAh) 2. Capacity percentage and totem pole display 3. Battery voltage 4. Battery current 5. Power output 6. The remaining time of charging and discharging
-
product
DC Load Bank
K-900
Kongter Test & Measurement Co., Limited
K-900 series are your best choice DC load bank with Kongter’s updated solutions. This new series resistive dummy load includes a series customized load bank models that feature rugged design and and excellent performance. They facilitate your work for DC load and battery capacity testing. With different models of DC load bank, it covers a wide range from 12V to 480V nominal voltages with current up to 600A. Its big TFT touch screen with vivid display makes it more user-friendly for setting and operation. Kongter’s new PC software make it easy for measurement monitoring and report print out.
-
product
Battery Analyzers
Beta D-50
*Analyzer for any type of battery.*Adjustable constant current discharge from 0 to 50 Amps.*Set for Amp-Hour capacity reading.*Accept or Fail lights Indicators for a GO/NO-GO Test.
-
product
Stationary Battery Comprehensive Tester
SAT-AG Series
Shaanxi Aitelong Technology Co., Ltd
SAT-AG Series Stationary Battery Comprehensive Tester is a kind of product introduced according to the market demand, which integrates the two major functions: on-line monitoring and capacity check test, with higher integration and better functions.SAT-AG is specifically designed for the maintenance of the lead-acid battery discharge in the electricity and telecommunication sector. It is a new high-tech intelligent product that provides safe, reliable and convenient constant testing equipment for the DC system(Direct current system) users.
-
product
GAOTek Handheld Digital Satellite Finder
A0N00021tek
GAOTek Handheld Digital Satellite Finder is designed to quickly and accurately align the antenna to the best position. This satellite finder can be used for DVB-S/S2 and ABS-S signal measurement. The embedded video and audio decoders also allows installers receive and plays standard definition unencrypted DVB-S TV channel signals directly on the 3.5 inch high definition color LCD screen. It supports many types of LNBs and the high capacity Li-ion battery can provide 500 mA current to LNBs.
