Filter Results By:
Products
Applications
Manufacturers
Temperature Sensors
Convert temperature into a measurable electrical signal.
- Pickering Interfaces Inc.
product
PCI High Density Pecision Resistor Card, 6-Channel, 3.5Ω To 773kΩ
50-298-043
The 50-298-043 is a high density programmable resistor card with 6 channels which can be set between 3.5Ω and 773kΩ with 1Ω resolution The 50-298 range provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-298 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
-
product
Air Temperature and Relative Humidity Sensors
Air temperature and relative humidity probes typically consist of two separate sensors packaged in the same housing. Often relative humidity is measured with a capacitive RH sensor, while air temperature is measured by a PRT.
-
product
Temperature Calibration Software v5.1
MET/TEMP II
MET/TEMP II software allows you to easily automate the calibration of a wide range of temperature sensors. It provides a comprehensive temperature calibration solution that allows you to test large quantities of sensors, calculate characterization coefficients, and print calibration reports. You can standardize comparison or fixed point calibrations and use multiple temperature sources or references in one test.
-
product
Qwiic Pressure/Humidity/Temp (PHT) Sensor - MS8607
The MS8607 from TE is an impressive combination pressure, humidity, temperature (PHT) sensor with accuracy of ±2mbar pressure, ±3% humidity, and ±1°C. Perfect for sensing general weather conditions the MS8607 really shines for high altitude, low pressure applications. Capable of sensing down to 10mbar, this pressure sensor separates itself from many other I2C pressure sensors like the BME280. The MS8607 is simple to use and gives the user some very powerful readings with very little power and conversion time.
-
product
5-in-1 Moisture Meter with METERLiNK®
FLIR MR77
The FLIR MR77 has everything you need for moisture remediation or HVAC: a pinless moisture sensor and pin probe, a temperature and relative humidity sensor, and an IR thermometer. The meter includes Bluetooth® for remote viewing and sharing, as well as METERLiNK® technology to wirelessly embed readings into radiometric infrared images on compatible FLIR thermal cameras. Made with field-replaceable sensors, the MR77 is engineered to help you get more done in less time.
-
product
Temperature Measurement IR Sensors & Detectors
ST60 TO-18
A single-channel silicon-based thermopile provides lowest cost solutions in a small active area of 0.61mm x 0.61mm in a small TO-18 package. Time constant of 18ms with Nitrogen encapsulation gas. Delivers a very low Temperature Coefficient of Responsivity of -0.04%/C. This detector has a very short thermal shock response to ambient temperature change.
-
product
Process Indicators & Field Devices
Field devices from the Field Analog series record and convert signals from resistance temperature detectors, thermocouples, resistance-type sensors, and voltage sensors directly on site.
-
product
Analog Temperature Sensors
Analog Devices analog temperature sensors provide current or voltage output proportional to the absolute temperature with accuracies of up to ±1°C. Our diverse range of analog output temperatures sensors can be used in a broad range of applications with no need for external calibration, and with minimal signal conditioning/conversion circuitry. To better suit your varied design needs, our portfolio of temperature sensors are available in multiple package options.
-
product
Soil and Air Temperature Probe
TP32MTT.03.B
Temperature probe with two 4-wire Pt100 1/3 DIN sensors for measuring the soil and air temperature (± 50 mm).
-
product
Pyrometer Calibration
Tempsens offers calibration of Non contact temperature sensors i.e. Infrared pyrometers traeceble to both national and international standards. Infrared thermometers can be calibrated at our NABL accredited laboratory, from 0ºC to 2900ºC utilizing state-of-the-art blackbody sources.
-
product
PXI Precision Resistor Module 6-Channel, 2.5 to 201k
40-297-041
This 6-channel PXI Precision Resistor Module provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-297 series is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
product
Weather Detection Systems
General offers weather detection systems that use a base station to display inputs received wirelessly from remote sensors. The RGR150 can track rainfall amounts as well as temperature and/or relative humidity. WS821 & WS831DL Weather Detection Systems are full-featured wireless weather stations that add wind speed readings and track trends in barometric pressure that can serve as the basis of a short-term weather forecast. Barometric pressure is also available from a dedicated wireless station (the DBAR880), and the original weather forecasterthe ABAR300 Analog Barometer.
-
product
NI-9219, 100 S/s/channel, 4-Channel C Series Universal Analog Input Module
785994-01
100 S/s/channel, 4-Channel C Series Universal Analog Input Module - The NI‑9219 is designed for multipurpose testing. With the NI‑9219, you can measure signals from sensors such as strain gages, resistance temperature detectors (RTDs), thermocouples, load cells, and other powered sensors, as well as make quarter-bridge, half-bridge, and full-bridge current measurements, with built-in voltage and current excitation. Each channel is individually selectable, so you can perform a different measurement type on each channel.
-
product
Sensors
Our technologies enable measurement capabilities such as pressure, temperature, position, vibration, photonics, force, and humidity.TE Connectivity offers an unmatched portfolio of intelligent and efficient sensors across patient monitoring and treatment and industrial automation applications. Browse from our portfolio to find the suitable sensor to create a safer, more productive, and reliable future together.
-
product
RH+T+Tdp Cable Probe
T3111-4
Relative humidity, temperature sensors at probe on the cable. Measured values are also converted to other humidity interpretation: dew point temperature, absolute humidity, specific humidity, mixing ratio, specific enthalpy.
-
product
Gas Flow Sensors
ESRF-ESF Sensor
ESRF-ESF is one of the few gas flow sensors featuring bidirectional gas flow sensing of up to ±300 ln/min with a total error band of < 1.25% RD. ESRF-ESF gas flow sensors provide calibrated and temperature compensated output on an SPI, I2C bus or analog output making them plug & play for direct interfacing to low voltage MCUs and systems. The user is provided with a multitude of interface and output options so that the right sensor configuration can be selected based on the specific requirements for each application.
-
product
High End Current Sensors
AC and DC currents with an accuracy down to 1ppm. Our standard products offers the following features: Automotive current sensors. Extended temperature current sensor - 85 deg Celcius. AC current sensor - DC current sensor.
-
product
J-Type Thermocouples Grounded (32 deg F to 900 deg F )
745685-J01
J-Type Thermocouple, 32°F to 900°F Temperature Sensor - The J-Type Thermocouple works with NI measurement devices and software to help you acquire temperature data within a measurement system. You can use LabVIEW or FlexLogger software and NI-DAQmx driver software to configure measurements and predefined scaling coefficients for the J-Type Thermocouple and acquire synchronized temperature data in units of degrees. The J-Type Thermocouple is available in various lengths and configurations including field-cuttable, ready-made sensors, and thermocouple wire extensions with a -20°F to 221°F temperature range.
-
product
Suitable For Temperature And Potentiometer Sensors
SEM1600T
The SEM1600T accepts resistance or mV signals from RTD, Slidewire or Thermocouple sensors.
-
product
Humidity and Temperature Transmitter
T3111Ex-2
Relative humidity, temperature sensors at probe on the cable. Measured values are also converted to other humidity interpretation: dew point temperature, absolute humidity, specific humidity, mixing ratio, specific enthalpy.
-
product
PXI Precision Resistor Module 6-Channel, 2.5 to 395k
40-297-042
This 6-channel PXI Precision Resistor Module provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-297 series is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
product
High-Temperature Zeus PEEK FBG Cable Sensor
Technica Optical Components, LLC
The T150 is a ruggedized high temperature non-metallic cable sensor designed for monitoring distributed temperatures and strains in environments to 260 Degrees Celsius with submillisecond response time. High temperature resistant non-metallic sensor. Ideally suited for applications where there is concern that the high temperature or chemical composition of the surrounding environment will cause damage to the sensors.
-
product
Portable Calibration Baths
6109A / 7109A
The Fluke Calibration 6109A and 7109A Portable Calibration Baths are liquid baths that let process industry professionals calibrate four times more sanitary sensors per batch in less time and with twice the accuracy of other portable baths in this class. Larger than micro baths, up to four tri-clamp sanitary sensors fit easily into these baths for calibration at ± 0.1 °C temperature display accuracy. Throughput is even higher for sanitary RTDs with small or no flanges. Two bath models cover a wide temperature range: 35 °C to 250 °C for the 6109A and -25 °C to 140 °C for the 7109A. Each model offers a “-P” version that includes process electronics for connecting an external reference probe. Professionals working in clean process industries, including facilities managers, production engineers and calibration technicians, prefer these baths for a variety of reasons.
-
product
Automotive Sensors
Sensors enable the ability to measure parameters such as pressure, temperature, and humidity to make cars more efficient, increase performance, and safer.
-
product
Con50
AMETEK Sensors, Test & Calibration
Con50 configuration software provides a way to configure and calibrate smart sensors for the RTC, PTC, and CTC temperature calibrators.
-
product
Temperature and Humidity Duct Mount Transmitter
T3413
Relative humidity, temperature sensors at 150mm stem. Measured values are also converted to other humidity interpretation: dew point temperature, absolute humidity, specific humidity, mixing ratio, specific enthalpy.
-
product
PXI Precision Resistor Module 6-Channel, 3 to 5.82M
40-297-052
A simple solution for applications requiring accurate simulation of resistive sensors. The series is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
product
PXI Precision Resistor Module 4-Channel, 1.5 to 472
40-297-120
This 4-channel PXI Precision Resistor Module provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-297 series is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
product
High Temperature Axial Torsional Extensometers (1200 C or 1600 C)
Model 7650
Jinan Testing Equipment IE Corporation
Model 7650 extensometers are primarily used on round specimens tested in bi-axial test machines capable of simultaneous axial and torsional loading. All models are capable of bi-directional displacement in both axes and may be used for strain-controlled fatigue testing under fully reversed load and strain conditions at frequencies up to 10 Hz.All 7650 models mount rigidly on the load frame and incorporate slide mounting to bring the extensometer into contact with the specimen. The gauge length is set automatically before mounting on the test specimen, which allows for hot mounting after thermal equilibrium has been reached.These units are specifically designed to minimize crosstalk between axes and to provide high accuracy, high resolution measurements. They incorporate capacitive sensors for low operating force and include electronics with programmable filtering and multi-point linearization for improved performance and accuracy. The overall design minimizes, and in many cases virtually eliminates, any influence from common lab environment vibrations.These water-cooled extensometers are equipped with high purity alumina rods with conical rod tips for specimen contact when testing to 1200℃(2200°F). Silicon carbide rods are used for the 1600℃ (2900°F) high temperature option.
-
product
3-CH RTD Input Module
ND-6013
ADLINK's NuDAM data acquisition modules make up a total acquisition network and control system. Up to 256 NuDAM modules an be romotely controlled on any RS-485 network from a host computer, via a single serial RS-232, allowing communication from as far as 4000 feet from the host. Based on the RS-485 multi-drop network system, each module has a unique address ID, whereby simple ASCII command & response protocols through the standard RS-485 interface can control all the NuDAM modules in the RS-485 network. The NuDAM modules provide direct communications with a wide variety of sensors, perform all signal conditioning, scaling, linearization and conversion, and can acquire measurements of temperature, pressure, flow, voltage, current, and multiple digital signal types.
