Filter Results By:
Products
Applications
Manufacturers
- Pickering Interfaces Inc.
product
Cable Assembly 44-Pin D-Type Male to Unterminated With Cut Ends, 2m
A044HM5-C-0A200
The 44-Pin Connector to Unterminated Cable Assy is constructed from PFA insulated 7/0.15 (26AWG) Silver Plated Copper Wire. The connector can be secured to the product by screwlocks. The unterminated connections are coded to match the connector pin designation . Please ensure appropriate electrical safety precautions are observed when using this product.
-
product
Hand Held Safety Analyzer
Rigel 288
The Rigel 288 is the FIRST universal truly hand-held medical electrical safety tester to combine the features of an automatic / manual tester with a data logging / asset management facility. In addition to IEC 60601-1 and AAMI / NFPA 99, the Rigel 288 tests to the new standard for in-service and after repair testing of medical electronic devices, currently drafted in as the IEC 62353.
-
product
Electrical Testers
When you work with electricity, you want tools that are field tested and proven to meet the highest standards. All Amprobe tools undergo rigorous examination in our state of the art testing labs, ensuring quality and full compliance with the latest IEC and CE safety regulations. They are also listed with third party certification labs worldwide. Amprobe electrical testers include circuit tracers and testers, non-contact voltage detectors, voltage meters, socket testers and more to cover all aspects of electrical testing.
-
product
Cable Assembly 15-Pin D-Type, Male to Unterminated With Ferrules, 1m
40-972-015-1m-MU
The 15-Pin Connector to Unterminated Cable Assy is constructed from PFA insulated 19/0.18 (21AWG) Tinned Copper Wire. The connector can be secured to the associated product by screwlocks. The unterminated connections are coded to match the connector pin designation and include crimped on ferrules to ensure the wire strands cannot break when they are terminated. When using this product additional cable strain relief arrangements may be necessary and appropriate electrical safety precautions should be observed.
-
product
Electrical Safety Testers
.AC/DC withstand voltage test & ground bond test .Insulation resistance test(ST60).Arc detection.Zero crossing turn-on,turn-off operation switch.Controllable ramp-up time .Ture RMS cut-off current measurement .Automatic fail indicator of alarm lamp and buzzer.VFD display.Standard PLC interface .Option RS-232,RS-485
-
product
Electrical Safety Wall
AllWin Instrument Science and Technology Co., Ltd.
1. Electricity Safety Wall2. 50/60HZ3. Four detection ways4. Continuous testing
-
product
Cable Assembly 15-Pin D-Type, Female to Unterminated With Cut Ends, 2m
A015DF4-C-0A200
The 15-Pin Connector to Unterminated Cable Assy is constructed from PFA insulated 19/0.18 (21AWG) Tinned Copper Wire. The connector can be secured to the associated product by screwlocks. The unterminated connections are coded to match the connector pin designation. When using this product additional cable strain relief arrangements may be necessary and appropriate electrical safety precautions should be observed.
-
product
Physical
This category covers test equipment for verification of resistance to heat, fire, tracking, mechanical stress, endurance, impact, force, torque, dimensional accuracy & similar related parameters as required by national and international safety regulatory agencies. These equipment are used to check Electrical WiringAccessories, Electrical Home Appliances, Industrial Luminaires, Motors and components or parts used in such products. Many of these test equipment are common to many standards and are essential for routine test purposes.
-
product
12-24V Multi-functional Auto Tester With LCD Display
6511
Peaceful Thriving Enterprise Co Ltd
Test the automotive electrical system within 12-24V. In order to save the testing hours for the automotive electrical system, the tester is designed to test the system without re-connection between the vehicle battery and the testing components. For the testing and safety purpose, the tester contains short-circuit protection, which can also check the ground connection without voltage drop test. The short-circuit protection system contains the recoverable fuse, so the technician will not waste the fuses during the testing. The extension cable is long enough for a technician to test the whole system for the vehicle. Therefore, the technicians do not have to search for ground connection constantly.
-
product
Test Phone - Industrial (3-way Lead)
CZ20124
The CZ20124 is the first of the industrial buttinskis focusing on ruggedness, reliability, and safety. DropSafeTM and RainSafeTM technology make these butt sets practically indestructible and the voltage and current protection technologies protect you from electrical hazards. The CZ20124 comes equipped with a multi-way lead set as standard meaning connection to Krone and RJ sockets are automatic. All the features of the base model butts are included making a truly valuable test phone.
-
product
Insulation & Continuity Multimeter
NEPTUNE
NEPTUNE is a mix of technology including an instrument for electrical safety testing (insulation up to 1000V and continuity with 200mA), a Harmonics analyzer and a TRMS multimeter.
-
product
Electrical Safety Analyzers
Fluke Biomedical electrical safety analyzers provide accurate and reliable results, helping you meet your medical device testing and quality requirements while ensuring patient safety.
-
product
Safety
Test Equipment to verify Safety, Quality and Compliance characteristics of electro-technical products as required by national and international safety regulatory agencies. These equipment are used to check Electrical Wiring Accessories, Electrical Home Appliances, Industrial Luminaires, Motors and components or parts used in such products. Several of these safety test equipment are common to many standards and are required for routine 100% test purposes to ensure product safety.
-
product
PC Controlled Bench Top Power Analyzer
PA2100
The PA2100 is a PC controlled bench top power analyzer, allowing several electrical power measurements to be taken simultaneously during testing - from just one set of input connections. The PA2100's power measurement ability is a must in research and development, manufacturing and required for certification and traceability of manufactured goods. In addition to power measurements, apparent power (VA), harmonics, voltage, current, power factor can all be viewed and stored with ease. The PA2100 wattmeter simply connects between the ac supply and the load, various current transformer options allow measurement with any size of current from 10mA to 10000A. Typical watt meter applications include appliance testing; microwave ovens, electric stoves, heating, air conditioning, TVs, monitors, computers, electronic lighting, fans and motor controllers. Powertek wattmeters are equipped with 4mm/banana safety terminals along with optional "breakout" boxes and clamp current probes for fast and safe measurement.
-
product
sbRIO-9269, Non-Enclosed, 100 kS/s/ch Simultaneous, ±10 V, Isolated, 4-Channel C Series Voltage Output Module
781120-01
Non-Enclosed, 100 kS/s/ch Simultaneous, ±10 V, Isolated, 4-Channel C Series Voltage Output Module - The sbRIO‑9269 is a channel‑to‑channel isolated analog output module. The sbRIO‑9269 adds channel‑to‑channel isolation for increased safety and improved signal quality. Channel‑to‑channel isolation is commonly needed for applications that have multiple electrical systems, such as automotive tests, or industrial applications that are subjected to increased noise and often contain multiple ground planes. Non-enclosed modules are designed for OEM applications.
-
product
PCI Express A/d Board
AD14-500x4-8GB-K7US
The AD14-500x4-8GB-K7US is a high performance wideband 4-channel 14-bit data single PCIe Gen3 board, that can continuously digitize four wideband signals, with four high linearity A/Ds.Designed for demanding military, medical, scientific, industrial, communications, safety and electrical power utility applications, these boards have a wideband noise figure of 10dB and 1 dB peak-to-peak ripple over the DC to 250MHz frequency spectrum (2dB p-p over DC-500MHz).
-
product
Loop Resistance Measuring Device According to DIN EN 61557-3 (VDE 0413-3)
PeakTech Prüf- und Messtechnik GmbH
A loop tester which is used to test the safety of electrical systems. These device measures the impedance of the short-circuit loop between the outer conductors of a circuit, whereby the probable short-circuit current is calculated. The protection of the circuit (miniature circuit breaker) must therefore trigger at a lower current than the expected short-circuit current, in order to avoid excessive heating of the lines and thus a fire risk. The PeakTech 2715 is due to its function and its robust design almost indispensable when performing new installations, but also for general checking of electrical systems, this device is the ideal companion.
-
product
Cable Assembly, 37-Pin D-Type, Female to Unterminated With Ferrules, 1m
40-972-037-1m-FU
The 37-Pin Connector to Unterminated Cable Assy is constructed from PFA insulated 19/0.18 (21AWG) wire and can be secured to the product by screwlocks. The unterminated connections are coded to match the connector pin designation and include crimped on ferrules to ensure the wire strands cannot break when they are terminated. Please ensure appropriate electrical safety precautions are observed when using this product.
-
product
Cable Assembly, 25-Pin D-Type, Male to Unterminated With Cut Ends, 2m
A026HM5-C-0A200
The 26-Pin Connector to Unterminated Cable Assy is constructed from PFA insulated 7/0.15 (26AWG) Silver Plated Copper Wire. The connector can be secured to an associated product by screwlocks. The unterminated connections are coded to match the connector pin designation. Please ensure appropriate electrical safety precautions are observed when using this product.
-
product
Cable Assembly 15-Pin D-Type, Male to Unterminated With Ferrules, 2m
40-972-015-2m-MU
The 15-Pin Connector to Unterminated Cable Assy is constructed from PFA insulated 19/0.18 (21AWG) Tinned Copper Wire. The connector can be secured to the associated product by screwlocks.The unterminated connections are coded to match the connector pin designation and include crimped on ferrules to ensure the wire strands cannot break when they are terminated. When using this product additional cable strain relief arrangements may be necessary and appropriate electrical safety precautions should be observed.
-
product
20-Pin GMCT Cable, Male to Unterminated, Tinned Ends, 10A, 1m
A020GMR-T-0C100
The 20-Pin GMCT cable assembly is constructed from 19/0.254 (18AWG) Tinned Copper Wire with PFA insulation. Screwlocks are provided to secure the connector to associated product. The unterminated connections are coded to match the connector pin designation. Users may need to make their own cable strain relief arrangements when using this product and should ensure appropriate electrical safety precautions are observed.
-
product
Calibration & Demag.
Model 8515-D
The Model 8515-D is a medium-energy, high voltage, and capacitor discharge type ringing demagnetizer capable of desaturating Ceramic and Rare Earth magnetic materials. The Model 8515-D is easily adapted to a wide range of production and laboratory demagnetizing requirements. A modern solid-state electronic control circuit, coupled with a rugged, heavy-duty discharge SCR and fixture, make this demagnetizer a highly reliable, low maintenance unit. The electronic voltage control circuit prevents the Model 8515-D from being discharged before the preset energy level has been reached, avoiding incomplete magnet desaturation. An easy to read front panel meter monitors the capacitor voltage. The energy storage level can be easily changed in the field. Integral electrical interlock and fail-safe circuitry provide a high degree of operator safety.
-
product
37-Pin D-Type Breakout DIN Female
40-967-037-F
This termination option is capable of accepting heavy duty connection wires and uses rising clamp screw terminals to minimize the danger of copper strand damage. Users should care take to protect the termination, provide a suitable method of restraining the cables, and ensure appropriate electrical safety precautions are observed.
-
product
Functional Safety
More and more devices, machinery, plants and systems contain electrical, electronic and/or programmable electronic systems and components. Malfunctions – also in sub-systems and components – can lead to hazardous situations for people, machines and the environment. If these systems contribute to the safety of the product, it is necessary that they function correctly under all circumstances (including possible failures and malfunctions). One speaks of functional safety in this context.
-
product
Cable Assembly 15-Pin D-Type, Male to Unterminated With Cut Ends, 1m
A015DM5-C-0A100
The 15-Pin Connector to Unterminated Cable Assy is constructed from PFA insulated 19/0.18 (21AWG) Tinned Copper Wire. The connector can be secured to the associated product by screwlocks. The unterminated connections are coded to match the connector pin designation. When using this product additional cable strain relief arrangements may be necessary and appropriate electrical safety precautions should be observed.
-
product
Vision-Pad Technology
vPad Series
Vision-Pad Technology uses an Android tablet to function as the display and control unit for our vPad series of electrical safety testing device. Find out more about Vision Pad Technology
-
product
Portable Appliance Testing
PAT
In response to ever growing industry requirements, Megger offers a sophisticated line of electrical product testing equipment. In today’s competitive electronic development industry, you don’t have a choice when it comes to the safety standards of your products. Government initiatives require all new electric products on the consumer and professional service markets to meet strict standards.
-
-
product
Voltage Detectors
JSC-88AW
The JSC-88AW is a very reliable way to know for sure whether or not there is voltage downstream from the switches or breakers during power-offs. It dramatically increases the safety of personnel assigned to maintenance work on electrical equipment powered by three-phase voltage. As long as voltage is present downstream of the breakers, one or more (LEDs) of the JSC-88AW will stay lit. A simple visual inspection tells you whether the electrical system is in “Zero Energy” mode. In addition, this new device has been improved to enable resistance to voltage spikes (transients).
-
product
Grid-Connection Testing System
This system is a power supply test system that performs grid-connection testing of distributed power sources (solar cells, fuel cells, gasoline engines, etc.)Enable inverter device testing that complies with the Agency for Natural Resources and Energy’s “Guidelines for System Interconnect Technical Requirements” and the Japan electrical Safety & Environment Technology Laboratories (JET) publication “Testing Methods for Small Solar Cell Power Generation System and System Interconnection Safety Devices”.
-
product
Photovoltaic and Electrical Installation Testers
Photovoltaic electrical installation safety testing is a special area of electrical installation safety testing as it also entails tests and measurements on DC systems, which are relatively uncommon in most domestic, commercial and to a certain extent industrial environments. There is also the addition of photovoltaic-specific tests that are outside the realm of standard test and measurement procedures.
