Filter Results By:
Products
Applications
Manufacturers
- Pickering Interfaces Inc.
product
PXI 10A Fault Insertion Switch 6-chan 2-bus
40-192-012
This PXI fault insertion switch uses solid state switching elements and is capable of switching current up to 10A. It is designed to be able to insert three different fault conditions between the test fixture and the equipment under test: Open-Circuit. Short-Circuit between UUT connections. Short-Circuit to external signals. Through relays on each channel enable signals to the UUT to be set open-circuit. Fault Insertion Buses allow any channel to be shorted to any other channel and also enable any channel to be connected to an external signal such as Power, Ignition or Ground to simulate fault conditions. The module is supplied with 2 fault buses.
-
product
Vacuum and Fuel Pump Tester
DVG1
Suitable for testing and fault finding the following in petrol engines including: Spark misfires; poor engine compression; weak/rich mixture; ignition over advanced/retarded; inlet manifold and carburettor air leaks; incorrect valve timing; poor fuel economy; balancing carburettors; turbo boost gauge; fuel pump testingDisplay packed.
-
product
Motor Vehicle Inspect Lines Engineer Program
Foshan Analytical Instrument Co, Ltd.
It is suitable for measurement of motor vehicles equipped ignition engine with max total mass more than 3500kg. Including the dual idle speed method test. Meet the requirement of GB18285-2005"Limits and Measurement Methods for Exhaust Pollutomts from Vehicles Equipped Igintion Eigine under Two-speed Idle conditions and simple Driving Mode Conditions". The system can select the prompt mode of the dirver mode or the prompt mode of lattice screen.
-
product
CDI Ignition Coil
An on-plug coil for use with Capacitive Discharge Ignition (CDI). Design and manufacture is in-house, so we can make the coil to suit your specific application. The information given here is for a typical coil. Many of the parameters can be tailored to a particular installation.
-
product
Noid Lights, IAC Test Lights & Ignition Spark Tester Kit
36330
Use to test electronic fuel injection signals, idle air control circuit and spark plug circuits. Quickly diagnose "no start" and engine miss conditions in the electrical fuel injection and spark plug circuits. Analyze rough running engines. Includes 8 Noid Lights (for checking GM PFI, FORD TBI, GEO TBI, BOSCH PFI, GM TBI, GM SCPI, BOSCH 2 and GM Multec 2; 2 IAC Test Lights (for straight and 90 applications); and Cat. No. 23900, In-line Ignition Spark Checker.
-
product
Hot Wire Ignition Tester
The HWI test indicates a materials resistance to ignition when exposed to abnormally high temperatures resulting from a component failure such as a conductor carrying far more than its rated current. HWI performance is expressed as the mean number of seconds required to ignite a specimen when wrapped with an energized non-chrome resistive wire that dissipates a specified level of energy.
-
product
6-24V LED Heavy Duty Circuit Tester
1646
Peaceful Thriving Enterprise Co Ltd
Check on 6, 12 and 24V systems. Quickly and safely test high and low voltages on all vehicle voltages, including computerized engine. High impedance to protect sensitive electronic sensors, microprocessors, electronic ignition components and air bags.
-
product
SPI Flammability Tester (Vinyl Material)
TF318
TESTEX Testing Equipment Systems Ltd.
SPI Flammability Tester (Vinyl Material), to determine the ignition properties of vinyl plastic film material according to CFR 16 Part 1611 U.S.A. Flammable Fabrics Act for flammability of apparel vinyl plastic film.The rate of burning shall not exceed 1.2 in./s as judged by the average of five determinations lengthwise and five determinations transverse to the direction of processing, when specimen is placed at an angle of 45 degree and expose to the standardized flame (22# fire nozzle, 1/2 inch. In length).
-
product
Multisystem Ignition Analyzer
TA500
The TA500''s unique and proprietary technology allows the user to perform quick and reliable diagnostics of non-starts, misfires, fouled up or damaged spark plugs and/or spark plug wires, by comparing digital read-outs of the spark plug voltage and spark burn time between cylinders on engines using Coil on Plug, Coil near Plug, conventional distributor/ignition coil, DIS (Distributor-less) or waste spark and magneto technologies.
-
product
ATEX / FM Approved Grounding Clamps, Cables and Reels
Cen-Stat Static Grounding Clamps
Static grounding systems like the Earth-Rite range combine interlock control and visual indication to verified ground connection points and offer the highest levels of protection over electrostatic ignition risks. However, equipment specifiers may select passive grounding devices, like single pole clamps, to ground and bond plant equipment.
-
product
AFC 45° Automatic Flammability Tester
M233G
To determine the burning characteristics of textiles under controlled conditions. Stainless steel test cabinet with glass observation panel provided with automatic timing of flame spread in 0.1 second increments from ignition.
-
product
Electronics & Power
Excelitas Technologies offers a wide range of high-performance electronics, power and energetics technologies to drive your most demanding photonic systems. Our Electronics & Power offering includes Capacitor Chargers, Spark Gaps and Transformers, High-Voltage DC Power Supplies and Atomic Frequency Standards. Our Energetics portfolio includes Electronic Safe & Arm devices, Detonators, Ignition Safety devices, and Rocket Motor Initiators.
-
product
Microwave Plasma Subsystems
AX2600 And AX2700
The AX2600 and AX2700 Microwave Plasma Delivery Subsystems are complete and highly reliable solutions for the cost-effective generation and safe delivery of atomic species to the wafer. Available in 3 kW, these highly reliable, field-proven plasma delivery subsystems deliver highly concentrated atomic species. Suitable for multiple chemistries, the high speed and precision of this plasma system’s automatic tuning guarantees immediate ignition and fast transition from plasma conditions for high productivity. Robust closed-loop control ensures high accuracy, precision, and optimal repeatability of the process from wafer to wafer and system to system.
-
product
Fanless AIoT Video Analytics Platform with NVIDIA Jetson AGX Xavier for Railway
AVA-RAGX
- NVIDIA Jetson AGX Xavier with 32 TOPs AI performance- 4xM12 GbE with PoE, 1x lockable HDMI output, 4x USB 3.0- 1x M.2 B-key for LTE/5G; 1x M.2 A/E key 2230 for Wi-Fi- 2x CAN DB-9 CAN-FD from AGX module, with isolation- Power with ignition control- Nominal Voltage: 24VDC, 36VDC, 72VDC and 110VDC (EN50155 compliant)
-
product
ATEX-Compliant IR Temperature Sensors
FLIR A310 ex
Explosive atmospheres need to be protected from ignition sources. Selecting equipment and protective systems which meet the requirements of the ATEX Product Regulations or similar regulations is essential. FLIR A310 ex is an ATEX compliant solution, with a thermal imaging camera mounted in an enclosure, making it possible to monitor critical and other valuable assets also in explosive atmospheres. Typical applications for the A310 ex include process monitoring, quality control, and fire detection in explosive locations. Because the FLIR A310 ex is rated IP 67, it can be installed in dusty environments. The Flame-Proof Enclosure "d"prevents any explosion transmission from the inside of the enclosure to the outside.
-
product
IEC60695 Needle Flame Test Machine
CX-Z18
Shenzhen Chuangxin Instruments Co., Ltd.
Needle Flame Tester is made according to Standard IEC60695 and GB5169, meanwhile it’s a synthesis test equipment that can meet related standard requirements. It’s mainly used to simulate technical evaluation interior equipment. It’s applied to the risk of ignition test of electrotechnical equipment, parts and elements, also suitable for the risk of ignition test of solid electrical insulating materials or other combustible material.
-
product
IGNITION COIL TESTER - ORANGE
MD76500M
*Non-intrusive, quick check tool instantly verifies active or inactive coil operation*Detects the magnetic field created by a coil energizing*Tool can be used to test coil on plug, coil near plug and coil pack systems
-
product
Carpet Flammability Tester
TF317
TESTEX Testing Equipment Systems Ltd.
Carpet Flammability tester is used to test the effects of a small source of ignition on floor coverings. Carpet flammability tester can be used for either Hot metal nut test (BS 4790) and Methenamine tablet test (ISO 6925, BS 6307 and GB/T 11049)
-
product
Intrinsically Safe Test Tools for Hazardous Areas
Intrinsically Safe is a protection method employed in potentially explosive atmospheres. Certificate IS tools are designed to prevent the release of sufficient energy to cause ignition of flammable material. IS standards apply to all equipment that can create one or more of a range of defined potential explosion sources.
-
product
Life Cycle Module Testing System
LCN
Full featured test system for quality control and R&DLife Cycle Testing: Perform charge/discharge cycling of batteries or modules to obtain charge and discharge capacity, energy and DC internal resistanceAutomotive Battery TestingStarting, Lighting and Ignition (SLI) TestingTraction Battery Testing
-
product
Motor/Gasoline Engine RPM Detector
OM-1500/1200
The OM-1500/1200 motor/gasoline engine RPM detector is designed for rotation measurement of a gasoline engine and an EV/HEV motor. It detects magnetic flux leakage from the motor itself or the engine’s ignition coil.This easy to use and durable detector can measure engine rotation by attaching in parallel with the ignition coil. When the EV/HEV motor rotation is measured, attach the OM-1500/1200 perpendicular to the motor rotating shaft.It is used with the engine tachometer by Ono Sokki (GE-2500, AR-7240B, CT-6520B, HT-6200, SE-1620, FT-2500, FT-7200).
-
product
Blanket Flammability Tester
TF316
TESTEX Testing Equipment Systems Ltd.
Blanket Flammability Tester, to determine the ignition resistance property of blanket fabrics and surface flame spread performance of fabric. A standardized flame is applied to the surface of specimen for a special time under controlled conditions, and burning, changing, or discoloration of a paper monitor is noted to classify flammability of tested fabric.
-
product
NFPA 701-2 Flammability Tester
TF321
TESTEX Testing Equipment Systems Ltd.
NFPA 701-2 Flammability Tester, to determine the ignition resistance properties of draperies and other hanging fabrics according to test method NFPA 701#2, and it is suitable for single-layer or multi-layer fabrics, fabrics with density larger than 700g/m2 (21oz/yd2), and fabrics coating with polyethylene, etc.
-
product
Ignition Driver Units
A compact inductive ignition drive unit which drives two banks of five ignition coils. The drivers are controlled via direct logic signals from a host ECU and provide fire-by-fire diagnostics back to that unit via CAN. The coils can be run at voltages up to 30V with this unit in order to minimize dwell times for optimum response.
-
product
Timing Lights
A stroboscope used to dynamically set the ignition timing of an Otto cycle or similar internal combustion engine equipped with a distributor. Modern electronically controlled passenger vehicle engines require use of a scan tool to display ignition timing.
-
product
Scalable T2G Onboard Gateway
AVA-1000
- EN50155 compliant- NXP i.MX8M Plus with Quad Cortex-A53- Intel Atom® 7th Gen series Amston Lake- Supports 3x 1GbE M12 LAN, 1x USB 3.0, 1x HDMI 2.0- Supports multiple connectivity of 5G, WiFi 6 and GNSS- Wide range 24-110VDC power input with ignition- Fanless extended temperature OT4, ST1
-
product
In Line HT Ignition Tester
1177
Establishes whether there is a high tension spark potential at the spark plug. Hands free operation means no risk of electric shock to user. Ideal for modern vehicles with sensitive electronics. Probe is 55mm long with a lead 100mm in length.
-
product
13 Pin Towing Socket Tester ( For Halogen Light System)
7630
Peaceful Thriving Enterprise Co Ltd
The tester is to connect with the 12V 13-pin Euro-type socket. It can also connect with 7 pin socket through a 13-7 pin towing adaptor. The cable is long enough for user to do the test while sitting in the vehicle. The tester can also do self-test (not work for 7 pin socket), 12V power check, ignition and reversing light. Not available for Newer car with LED light. CAUTION: The self-test is not available with 13-7 pin towing adapter because there is no continuous feed via the 7-pin socket.
-
product
Blanket Flammability Tester
TESTEX Testing Equipment Systems Ltd.
Blanket Flammability Tester, to determine the ignition resistance property of blanket fabrics(blanket fabric burn test). Blanket Flammability Tester complies with ASTM D4151, etc.
-
product
Automotive Tester
An automotive tester can be used to inspect one or more aspects of an automobile. For example, a borescope automotive tester is an automotive inspection camera used by auto body mechanics to see inside car, truck and other vehicle engines before removing any engine parts. Other kinds of automotive tester devices are used to adjust belt tension, test the electronic ignition starter, search for air conditioning leaks, measure the force required to press a brake pedal, determine the antifreeze concentration, or check the paint thickness over collision repairs.PCE Instruments (PCE) offers a wide variety of automotive tester products. These diagnostic support tools help professional automobile mechanics identify a number of vehicle repair needs. PCE's automotive tester products can aid in the diagnosis of many different mechanical and electrical system issues, including but not limited to locating the cause of an engine misfire, testing fuel injector resistance, pinpointing an engine coolant leak, or detecting car cylinder head problems. It's no wonder so many auto repair technicians choose to stock theirs shops and garages with PCE automotive tester products.
-
product
Battery Testing Chambers
ET-SERIES
These Chambers are designed and manufactured to meet various types of battery testing requirements of its customers by keeping all safety options in mind against any harmful explosions or ignitions and user safety while testing these batteries for environmental stress conditions
