Filter Results By:
Products
Applications
Manufacturers
Couplers
enable a signal to be used in another circuit.
- LBA Group, Inc
product
Digital RF Power Monitor
3024
The COMM-connect 3024 RF Power Monitor from LBA Technology can control up to 8 external RF Measuring heads. The high dynamic range with external couplers and RF measuring heads cover from 1W to 1MW. The Power conversion algorithms handles multi carrier, multi mode, peak, average and RMS signals. The power readout is auto scaled and VSWR can be calculated between any probes. Also the measured and calculated results along with alarms can be shown in the local LCD. The instrument has SNMP support to allow network management. The instrument can be configured for VSWR and Power limits to give alarms. The alarms can be configured to operate relay drivers or isolated Optcouplers. The alarms can also be configured as SNMP traps sending relevant information to the network control center. The COMM-connect 3024 WEB enabled RF Power Monitor gives an unlimited number of applications to monitor and control the last part of your RF network installation from transmitters to the antenna.
-
product
Solid State Relays
Panasonic Industrial Devices Sales Company of America
Panasonic offers a wide variety of Solid State Relays including Through-Hole and SMD, High Capacity and Phototriac Coupler Solid State Relays. Triac output components for AC load applications. Advantages include long operational life, high frequency switching, no contact arcs, high contact reliability, and noiseless operation.
-
product
FBG-Scan 700/800
FBG-Scan 700/800
The FBG-Scan 700 and 800 are dynamic, high precision measurement devices for Fiber Bragg Grating (FBG) sensors. The system can measure up to 40 FBG sensors using 2 input channels. Both input channels are simultaneously monitored using an optical coupler at a scan rate up to 2000Hz.
-
product
Wire Systems Analyzer
Console Test Systems (CTS)
Wire Systems Analyzer Commercial Roll around detects and locates faults and detects degradation in electrical interconnect systems ranging from simple to complex. Used to verify the operation of relays, circuit breakers, indicators, switches, diodes, transformers, 1553 couplers, etc.
-
product
Combiners
The Amphenol Procom Combiner systems secure a safe combining of multiple Tx channels and splitting of multiple Rx channels transmitted to and received from a base station antenna. Amphenol Procom’s Combiner selection includes Compact Combiners, Cavity Combiners, Hybrid Combiners, Receiver Multicouplers, Power Splitters and Dividers, Couplers, Low Noise Amplifiers, Power Monitors and various Combiner Components.
-
product
Voltage Input Module For Remote I/O
The Voltage Input Module for Remote I/O features 2-, 3-, and 4-wire spring terminal connection methods, a built-in power supply for sensors, four selectable input ranges, and simultaneous sampling. A remote I/O system consists of an EtherCAT bus coupler and individual modules mounted on a DIN rail. You control the Voltage Input Module for Remote I/O from a real-time controller, such as a CompactRIO Controller or an Industrial Controller. You can use remote I/O hardware to add low-cost I/O for simple tasks while your controller handles advanced tasks such as image processing, motion control, and high-speed or specialty measurements.
-
product
Couplers
Smiths Interconnect range of passive coaxial products include couplers of various types (Wilkinson, Directional and Branchline) designed specifically for established reliability applications to provide optimal performance operating in assigned frequencies ranging from UHF to Ku-Band. The couplers featured below have been developed and qualified to operate in extreme operational environments whilst providing designers and system architects with reliable and robust products produced by a manufacturing team experienced in the production of critical application hardware.
-
product
RF Couplers
Directional, bi-directional, dual-directional and RF Taps; over 475 models with power handling from 0.5 to 300W covering DC to 65 GHz!
-
product
Coaxial Directional Coupler, 1 GHz to 20 GHz
87300B
The Keysight 87300B is a compact, broadband directional sampling coupler designed for signal monitoring or, when combined with a coaxial detector, signal leveling. It is supplied with SMA female connectors.
-
product
IPM Drive
IPM drive photocouplers (optocouplers) are optically coupled isolators containing a GaAlAs LED on the input side and a photo diode and signal processing circuit on the output side in a single chip. This coupler is a high common mode transient immunity (CMR), high CTR type whose pulse width changes according to the operating temperature, making it ideal for driving IPMs (intelligent power modules).
-
product
Couplers
We offer SMA, 2.92mm, & 4.3/10 Directional couplers, useful in tapping off a portion of a signal, often for monitoring purposes. The 4.3/10 Couplers are low PIM.
-
product
Antenna Coupler, 300 MHz - 6 GHz
dbCOUPLER
The dbCOUPLER is ideal for many different applications including security, GNSS, Bluetooth, WiMAX, Wi-Fi, 5G, LTE, and RFID (vUHF SHF).
-
product
Coupler And Decoupler Used With Lightning Impulse Simulation Tester
All electric equipments & systems is required Impulse Simulation Test to the to be tested under the condition where the power source is applied to the product-under-test.At this test condition, the decoupler is needed to reduce the impulse flowing through the power line while testing. And the coupler which is inserted between tester and product, to simulate the actual condition, so the electric circuit of decoupler is prescribet by IEC rules.
-
product
Couplers & Power Dividers
*High power handling 750W Ultra-broadband devices support from 555 to 3800 MHz*Very low PIM <-160 dBc with low insertion loss*Outdoor rated unit with support for 7-16 and 4.3-10 connectors*Designed and produced to ISO 9001:2008 centrfication standards for reliability and quality
-
product
Diode Power probe
The COMM-connect 3026 Diode based temperature compensated probe is designed for use with the COMM-connect range of Power Monitors. The probe will handle from 50µW to 100mW . Used with external couplers and the our measurement system application from 1W to 1MW, a high dynamic range can be configured. The 3026 Diode based probe gives excellent stable results along with the COMM-connect Power Monitor variants. This gives our customers a number of applications to monitor and control the last part of your RF network installation from transmitters to the antenna.
-
product
Waveguide Coupler
ZDC8-30W32.9-50G-2389
Crossguide Coupler, Frequency 32.9~50GHz, Coupling 30dB, Waveguide FUGP400, 2.4mm Female
-
product
3D Electromagnetic Simulation Software
Efield® offers a complete and unique integrated modelling and simulation environment for 3D analysis of a wide range of electromagnetic applications such as: Antenna design All kind of antennas including horn, reflector, wire and microstrip antennas as well as broadband antennas and antenna arrays. Antenna integration Radiation pattern of installed antennas on large platforms such as aircraft or ships. Coupling between installed antennas. Microwave design Typical applications includes design of filters, connectors and couplers. EMI/EMC interaction Analysis of a wide range of EMC/EMI problems including shielding and coupling. Scattering & radar cross-section RCS analysis of structures such as aircraft, ships, air-intakes, exhausts, and antennas.
-
product
Passive Components
Ducommun millimeter wave products include various passive components including multi-hole directional couplers (PCM), crossguide couplers (PCC), magic tees (PCT), coax power dividers (PPD), bandpass, low pass and high pass filters (PFB, PFL and PFH), waveguide diplexers (PDC), waveguide transitions (PRC and PTW), waveguide to coax adapters (PTC) and waveguide components (PWS, PWE, PWH, PWM and PWT). These passive components cover frequency range from 8.2 to 110 GHz and feature high performance and low cost.
-
product
Simulating Optical Design Components
Wave Optics Module
The Wave Optics Module provides dedicated tools for electromagnetic wave propagation in linear and nonlinear optical media for accurate component simulation and optical design optimization. With this module you can model high-frequency electromagnetic wave simulations in either frequency- or time-domain in optical structures. It also adds to your modeling of optical media by supporting inhomogeneous and fully anisotropic materials, and optical media with gains or losses. It is straightforward to simulate optical sensors, metamaterials, optical fibers, bidirectional couplers, plasmonic devices, nonlinear optical processes in photonics, and laser beam propagation.
-
product
Antenna Couplers
Concentric Technology Solutions, Inc.
RF Antenna Couplers help create the ideal environment for shield boxes by providing a consist, stable and reliable environment for repetitive over the air (OTA) tests.
-
product
Linear IC Tester
570A
The Model 570A Analog IC Tester's built-in test library includes all common Analog ICs including op-amps, comparators, voltage regulators, voltage references, analog switches & multiplexes, opto-isolators & couplers, and audio ICs.
-
product
REM-11120, 4-Channel Thermocouple, 1-Channel Voltage, Temperature Input Module for Remote I/O
784750-01
4-Channel Thermocouple, 1-Channel Voltage, Temperature Input Module for Remote I/O - The REM‑11120 is a temperature input module for remote I/O. Remote I/O systems are low-cost, modular systems for simple machine control and measurements. A remote I/O system consists of an EtherCAT bus coupler and individual modules mounted on a DIN rail. You control the REM‑11120 from a real-time controller such as a CompactRIO Controller or an Industrial Controller. You can use remote I/O hardware to add low-cost I/O for simple tasks while your controller handles advanced tasks such as image processing, motion control, and high-speed or specialty measurements. The REM‑11120 also has an adjustable filter time for improved measurement quality and optional external cold junction compensation (CJC) or PT100 resistance temperature detector (RTD) measurements.
-
product
Cross Needle Meter. 1.8 - 60/144/440
MFJ-864
This new MFJ Cross Needle SWR/Wattmeter covers HF thru VHF 1.8 - 60MHz, 144 MHz and 440 Mhz bands. It features separate HF and VHF / UHF directional couplers, each with its own SO-239 connectors. This lets you connect your HF and VHF/UHF transceivers at the same time.
-
product
Immunity Testing Systems
CIS Series
The CIS series test systems are configured to perform conducted immunity testing according to IEC 61000-4-6. The system includes an ACS series power amplifier, coupling/decoupling Network (CDN), directional coupler, 150Ω to 50Ω adapters, power attenuators, cables and [optional] CSAT software. These systems, when properly configured, are capable of testing your products to all levels given in IEC 61000-4-6 up to 230 MHz. You can choose from three systems. Follow the links below for detailed information, including a comprehensive datasheet listing system specs.
-
product
3x3 and 2x2 High NA Couplers
Feasa produces a range of Couplers Manufactured from high Numerical Aperture (NA) 80 micron fiber. High NA fiber has low bend attenuation compared to standard singlemode fiber.
-
product
Couplers Splitters And Multiplexers
Passive optical devices that are used to split an optical signal into at least 2 and as many as 64 signals.
-
product
PCI Express to VME Interface
SIS1100-E2/3104-2
The SIS1100-e2/SIS3104-2 interface/bus coupler is the choice for demanding VME readout applications. VME block tranfser speeds up to 160 MByte/s are readily accomplished in conjunction with state of the art VME slave hardware.
-
product
RF Front-end
The RF integrated passive device (RF IPD) uses a high-resistivity substrate to integrate quality factor components such as capacitors and indictors. Many functions like impedance matching networks, harmonic filters, couplers, baluns, and power combiners/splitters can be designed using IPD technology. ST's IPDs are manufactured using thick film and HiRes Si or glass wafer manufacturing technology and photolithography processing.
-
-
product
REM-11152, 16-Channel (Input), 24 V, 2-, 3-, 4-Wire Digital Module for Remote I/O
784743-01
The REM‑11152 is a digital input module for remote I/O. Remote I/O systems are low-cost, modular systems for simple machine control and measurements. A remote I/O system consists of an EtherCAT bus coupler and individual modules mounted on a DIN rail. You control the REM‑11152 from a real-time controller, such as a CompactRIO Controller or an Industrial Controller. You can use remote I/O hardware to add low-cost I/O for simple tasks while your controller handles advanced tasks such as image processing, motion control, and high-speed or specialty measurements. The REM‑11152 features 2‑, 3‑, and 4‑wire spring terminal connection methods, a built-in power supply for sensors, and an adjustable filter time to improve measurement quality. You can use inputs as counters or standard digital inputs.
