Filter Results By:
Products
Applications
Manufacturers
- Cytec Corp.
product
Solid State Digital Matrix Switching Systems
DX Series
Cytec's DX Series Switching Systems are based on solid state switch fabric. All systems are non-blocking (any input to any output) and full fan-out (any input to any or all outputs)The DX/256x256 systems are designed to switch TTL, CMOS, LVTTL, IRIG, RS232 and RS422 up to 80 Mbps NRZ. Input and output buffers are used to convert to RS422 and/or RS232 signal levels as needed.The DXM/64x64 and DXM/128x128 are modular systems capable of switching data rates to 3.2 Gbps NRZ. They are intended to switch RS422, ECL, PECL, LVDS, CML and virtually any type of digital data stream. Configurations as large as 128x128 Clock and Data systems can be easily configured.The DX/64x64 is an earlier version of the DXM and offers systems up to 64x64 with SMA connectors for ECL, PECL, LVDS or RS422.
-
product
Faraday Cages
LBA's EMFaraCage® faraday cages are EMI and RFI shielding boxes and RF test enclosures that bring convenience to device testing. Faraday cages are ideal for isolating critical systems in high field RF environments or wherever RF ingress or egress must be minimized. Security, production testing, biomedical research and semiconductor testing are only a few of the many areas where EMFaraCage® faraday shielded enclosures are employed. EMFaraCage® faraday cage enclosure systems are fully featured to support a wide variety of test missions. The standard faraday cages include effective power, dataline and RF signal isolation in large test volumes. EMFaraCage® faraday cages are much more affordable than shielded room solutions and offer the convenience of portability.
-
product
Preamplifiers
Com-Power broadband high gain preamplifiers were designed for electromagnetic interference (EMI) testing and certification. EMC test labs use preamplifiers to improve sensitivity of the test system during EMI radiated emissions measurements. Without a high gain preamplifier, signals picked by the antenna that have amplitudes below the noise floor of the test system cannot be measured. The preamplifier gain has minimum variations for the entire operating frequency range for accurate emissions measurements. The Com-Power preamplifiers were primarily intended for EMC applications. However, it can be used for other applications that require signal amplification.
-
product
Mission Processor
58U91-03
- +28 VDC input- 9 DC outputs at 600 Watts- Provides system EMI per MIL-STD-461- Continuous Background Built-In-Test (BIT)- Temperature monitoring- I2C communication
-
product
Test Software
Elektra
The R&S®ELEKTRA test software controls complete EMC systems and automates measurements of equipment under test (EUT) being certified for emissions (EMI) and immunity (EMS). R&S®ELEKTRA simplifies configuration of test systems and test descriptions in accordance with common standards. It speeds up test execution and paves the way to quickly generating a comprehensive test report.
-
product
EMI Test System
EMI-9KA
EMI-9KA is an automatic EMI receiver. It is a main test system for EMI (Electro Magnetic Interference) testing. The EMI-9KA is produced by the full closure structure and strong electro-conductibility material, which has high shielding effect. Due to the new technology for the EMI Test System, it solved the instrument self-EMI problem. The test results are according to the international format test report. The EMI Test System EMI-9KA fully meets CISPRl6-1, GB17743, FCC, EN55015 and EN55022.
-
product
EMI and EMC Test System
EMI receiver system. It is a main test system for EMI (Electro Magnetic Interference) testing. The EMI-9KB is produced by the full closure structure and strong electro-conductibility material, which has high shielding effect. Due to the new technology for the EMI Test System, it solved the instrument self-EMI problem.
-
product
EOS Tester
KT-200SG
This test instrument stands for the EMI(Electro Magnetic Immunity) ability test to the electric devices, electronic circuit boards & electric equipments. Recently this instrument is widly used in many companies in Korea & other countries to test the immunity to thier products-power supply, drive PCBs, communication systems, LCD display panels whether they are safe or not against the impulse & noise.All for the purpose, of this object, it generates 4 ~ 5 kinds of different impulse test waveforms.Output test voltage level : 5 ~ 200 V ImpulseOutput voltage polarity : Positive, NegativeType of waveforms
-
product
EMI Receiver System
EMI-9KC/EMI-9KB
EMI-9KB is an automatic EMI receiver system. It is a main test system for EMI (Electro Magnetic Interference) testing. The EMI-9KB is produced by the full closure structure and strong electro-conductibility material, which has high shielding effect. Due to the new technology for the EMI Test System, it solved the instrument self-EMI problem. The test results are according to the international format test report. The EMI Test System EMI-9KB fully meets CISPRl6-1, GB17743, FCC, EN55015 and EN55022.
-
product
Receiver, 9050, 50 Module, Dual Discrete Wiring Tiers, EMI Gasket
310104429
The 9050, 50-module receiver is rugged and designed to accommodate high I/O and suited for larger test and measurement systems. Both tiers are designed for discrete wiring and can accommodate individual 9025 ITAs. This 9050 also offers a gasket for EMI applications.
-
product
Receiver, 9025, 25 Module, EMI Gasket
310104431
The 25 Module Receiver is a rugged system devised to accommodate medium I/O. With high contact point availability, the 25 Module Receiver is suited for larger test and measurement systems. This 9025 offers a gasket for EMI applications.
-
product
EMI Test Receiver
SER
Saluki SER series EMI receivers comply with CISPR 16-1-1 standard, integrated CISPR-AVG, CISPR-RMS, QPK detectors, and electromagnetic interference measurement. According to CISPR, EN, FCC and MIL standards, which is suitable for EMI testing in home appliances, lighting, automotive electronics, medical, and other industries. Combined with ETR PC measurement software and a wealth of test options, accurate automated testing is possible. The whole system is equipped with a spectrum analysis module and a tracking signal generator to meet the testing needs of users in different fields.
-
product
Emissions Test System
PC-114
Perform Radiated & Conducted EMI pre-compliance testing at your facility up to 1 GHz. Com-Power PC-114 EMI emissions test system is a ideal solution performing pre-compliance EMC testing from 9 kHz - 1 GHz.. It has essential equipment needed for radiated and conducted EMI emissions measurements. The system includes a spectrum analyzer, antennas, near field probes, a preamplifier, LISN and a non conductive antenna tripod. Pre-compliance testing in EMC is a commonly used term not easy to define. In general, it implies testing done prior to formal testing for legal compliance. Formal legal compliance is performed at a facility designed and equipped with test instrumentation that is fully compliant with the applicable EMC standards. Such facility and instrumentation is capital intensive and can be expensive even to rent and not easily available. Compliance testing is performed per exacting requirements of the Standards and other reference documents adhering to the test methods and last detail. In addition, the test facility may require to be accredited by an accreditation body such as NVLAP, A2LA. Often it is desirable to know prior to compliance testing at such facility, whether a product is close to compliance and also how close. Pre-compliance testing is specially useful for specifications such as FCC, Part 15, EN 55022 or EN 55011 (CISPR 22 or CISPR11). Pre-compliance testing usually means using the full compliance methods but making a few educated compromises in use of site or equipment to reduce costs and testing time. Here are some benefits of pre-compliance testing.
-
product
EMI Test System
TS9975
The R&S®TS9975 is the base system for conducted and radiated EMI measurements. Due to its modular design, it covers a wide range of applications and can be very easily adapted to the measurement task at hand. Any configuration is possible – from conducted measurements and the small precompliance system with a compact test cell to the accredited test system for large equipment under test. Combinations of different applications or incremental expansion are easily possible.
-
product
RSE Wireless EMC Spurious Emission
TS8996
The R&S®TS8996 RSE test system is designed for EMI and radiated spurious emission testing on wireless devices in semi-anechoic or fully anechoic chambers. The modular design makes it easy to extend the system to include new communications technologies. Typical devices under test include mobile phones or radio sets along with radiated measurements of other short-range devices. Standards require a wide range of test setups and a wide and high frequency range (up to 40 GHz). ESW or FSW frequency ranges are extended up to 325 GHz with option B21 using receive units TC-RSE for 5G FR2. Dedicated RSE test routines are also covered for this frequency range.
-
product
Regenerative Battery Pack Test System
17040
Conforms to international standards for battery testing: IEC, ISO, UL, and GB/T, etc.Regenerative battery energy discharge (Eff. >90%, PF >0.95, I_THD <5%)Multiple voltage and current ranges for auto ranging function to provide optimum resolutionHigh accuracy current/voltage measurement (0.05%FS/0.02%FS)2ms current slew rate (-90% ~ 90%)Dynamic (current/power) driving profile simulation tests for NEDC, FUDS, HPPCTest channel parallel functionTest data analysis functionData recovery protection (after power failure)Automatic protection for error conditionBattery simulator (option)High power testing equipment- Voltage range : 80~1000V - Current range : 0~750A - Power range : 0~300kWCustomized integration functions- Integrated temperature chamber - BMS data analysis - Multi-channel voltage/temperature recording
-
product
ESD Test System
58154 Series
ESD (Electrostatic Discharge) Test Systems are PXI/PCI controlled module to simulate electrostatic discharge pulse during electronic device testing. The 58154 series offer both ESD STM5.1-2001-Human Body Model and ESD STM5.2-1999-Machine Model. The user friendly software offers programmable and flexible features, such as sampling test on a wafer, ESD model, ESD pulse polarity, ESD pulse interval in a sequence, and automatic testing function.
-
product
Photonics Wafer Probing Test System
58635
The advancement of the photonics device technology continues to enable broader and more demanding applications in the industry.
-
product
OLED Lifetime Test System
58131
The 58131 Lifetime Test System is designed specifically for the OLED industry. Model 58131 provides twoquadrant constant current (CC) and constant voltage (CV) stimulus to each OLED panel and acquires electrical and optical characteristics automatically. Two independent and isolated precision source-and-measure units (PMU) are incorporated in one modular card, which is capable of testing two OLED panels. Additional instrument cards are added to expand test capacity. Hot plug and play is a key feature of 58131. When a UUT fails or an instrument card needs to be replaced, 58131 does not have to be shutdown and testing continues for other UUTs. Hot plug and play obviates life test cycle restarts due to isolated faults and significantly improves life test efficiency. We firmly believe that hot plug and play capability should be mandatory for all lifetime test systems.
-
product
VLSI Test Systems
50/100 MHz clock rate50/100 Mbps data rate1024 I/O pins (Max :1280 I/O pins)Up to 1024 sites Parallel testing32/64 M pattern memoryVarious VI sourceFlexible HW-architecture (Interchangeable I/O, VI, ADDA,)Real parallel trim/match functionTime & frequency measurement unit (TFMU)High-speed time measurement unit (HSTMU)AD/DA test optionSCAN test option (max 1G M/chain)ALPG test option for embedded memorySTDF tools supportTest program/pattern converter(J750, D10, V50, E320, SC312, V7, TRI-6020, ITS9K)User friendly windows 7 environmentCRAFT C/C++ programming languageSW (Software) same as 3380P & 3360P
-
product
Test System Replication/Build-to-Print
Need to manufacture test stations? For more than 15 years we have sourced, assembled, tested and shipped fleets of robust, cost-effective solutions. We produce them at our high-volume facilities and deploy them around the world.
-
product
Communications Test System for Frontline Diagnostics
ATS3000P
The ATS3000P is designed using Astronics Test Systems’ proven Synthetic Instrumentation architecture. Featuring 23instruments, and both Automated and Standalone modes to test, record, and diagnose faults, the unit provides complete RF, Analog and Digital capabilities. The ATS3000P also includes the sophisticated IF and baseband I/Q DigitalSignal Processing required for modern radios. The fieldupgradeable, software-defined architecture features easyto-use graphical user interfaces and enables testing with minimal operator intervention. Test Program Sets are available for a full range of tactical radios, or you can create new TPSs easily using the included TestEZ® software suite.
-
product
Current Caliper
KH23101
Beijing KeHuan Century EMC Technology Co,.LTD
The KH23101 current caliper is a toroidal transformer used to measure EMI current. When measuring, the caliper does not directly touch the electrical conductor or the cable under test. The conductor passing through the caliper window is used as the single-turn primary wire of the transformer, and the secondary is designed to be multi-turn. Use with 50 Ω receiving system (such as EMI electromagnetic interference field strength meter or spectrum analyzer). In order to facilitate installation and rapid measurement of EMI current, it is designed as a caliper that can be opened.
-
product
VLSI Test System
3380D
The 3380D/3380P/3380 test system have 4 wires HD VI source and any-pins-to-any-site high parallel test (multi-sites test) functions (256 I/O pins to test 256 ICs in parallel) that can meet the upcoming higher IC testing demands.
-
product
Advanced SoC/Analog Test System
3650
Chroma 3650 is an SoC tester with high throughput and high parallel test capabilities to provide the most cost-effective solution for fabless, IDM and testing houses.
-
product
Photodiode Burn-in Reliability Test System
58606
The Chroma 58606 PD/APD Burn-in system is a high density, multifunction and temperature controlled module based system for photo diode burn-in and lifetime test. Each module has up to 256 Source Measurement Unit channels which can source current and measure voltage in various scenarios such as one described below. The system can accommodate 7 modules for a total of 1,792 device channels.
-
product
Automatic Test System
Automatic Test system is the ultimate solution for power electronic testing. The system includes a wide range of hardware choice such as AC/DC Sources, Electronic Loads, DMM, Oscillate Scope, Noise Analyzer and Short /OVP Tester. This flexibility combined with its open architecture software platform-PowerPro III, gives users a flexible, powerful and cost effective test system for almost all types of power supply testing.
-
product
Test System
BMS HIL
The BMS Hardware-in-the-Loop (HIL) Test System is a high performance platform providing all necessary input signals used for battery pack simulation. A real-time operating system executes complex cell and pack models commonly used for BMS algorithm development and firmware regression testing.
-
product
PXI Semiconductor/IC Test System
A high-density 100MHz PXIe digital IO card designed for characterizing, validating, and testing a variety of digital and mixed-signal ICs. Each IO card consists of a Sequencer Pattern Generator (SQPG) and 32 channels of full ATE-like features. The 33010 IO card is expandable up to 256 channels. Some unique features of the 33010 include an on-board SQPG, per pin timing/levels/ PMU/TFMU, multiple time domains, and multithreaded testing for complex IC testing. Each channel is also equipped with 64M vector memory, 16 timing sets with on-the-fly timing change, and per pin timing and frequency measurements up to 400 MHz.
-
product
Iridium Physical Layer Test Systems
PLTS
Averna has worked with Iridium to ensure you have the right equipment to support their test coverage. The Iridium PLTS verifies product performance to Iridium’s standards. Find out more!
-
product
Battery Management (BMS) Environmental Test System
The BMS Environmental Test System is a configurable platform simulating the essential signals used by Battery Management Systems (BMS) and cell-monitoring modules with the ability to perform environmental testing on multiple BMS units simultaneously. The system implements single-point value testing to evaluate specific BMS functions such as cell over and under voltage scenarios, cell leakage current, lost communications, or faulty system IO.
