Filter Results By:
Products
Applications
Manufacturers
1553 Interfaces
Mil-Std-1553 interfaces.
- Pickering Interfaces Inc.
product
PXI/PXIe MIL-STD-1553 Multiplexer, Dual 4-Channel, 2-Pole
42-739-006
The 40-739-006 (PXI) and 42-739-006 (PXIe) are dual 4-channel 2-pole multiplexers designed specifically for physical layer multiplexing or demultiplexing differential signals that conform to the MIL-STD-1553 specification. The module can be supplied as a single or dual 16-channel 2-pole multiplexer with each signal pair having a controlled 78 Ohm differential impedance.
-
product
2 Channels, MIL-STD-1553, Dual Redundant, Direct Coupled, Assisted Mode Capable (AMC)
FTE
MIL-STD-1553 is a military standard published by the United States Department of Defense that defines the mechanical, electrical, and functional characteristics of a serial data bus. It was originally designed for use with military avionics, but has also become commonly used in spacecraft On-Board-Data-Handling (OBDH) subsystems, both military and civil. It features a dual, redundant, balanced-line, physical layer; a (differential) network interface; time division multiplexing; half-duplex command/response protocol; and up to 31 remote terminals (devices).
-
product
Interface Card - 1-2 Channels of MIL-STD-1553 Networks on a PMC Form Factor with Ethernet Backplane Interface
PMCE-1553
PMCE-1553™ is an innovative product that provides 1553 operations via 10/100/1000 Ethernet IP/UDP local area networks (LAN) backplane. PMCE-1553 is a standard PMC form factor card, but instead of PCI backplane, PMCE-1553 uses the P4 connector for Ethernet based control and communications.
-
product
PXI Interface Module, AIT MIL-STD 1553
M3406A
Interface to the LRU in avionics test solution Up to four channel MIL-STD-1553 bus interface with full error injection and detection Concurrent Bus Controller, multiple Remote Terminals (31), and Bus Monitor operation capabilities Data capture filtering, 100% bus recording, and physical bus replay Variable output voltage signal and software selectable bus coupling modes 10 high voltage (up to 30 V) programmable DIO lines PXI trigger generation on 1553 bus events
-
product
MIL-STD-1553 Test & Simulation Interface for VME
VME-1553
Avionics Interface Technologies
Dual redundant, single, dual, or quad stream configurationsTransformer & Direct Bus Coupling - Concurrent Bus Controller, 31 Remote Terminals, & Bus Monitor operation - Full error injection and detection - Multi-level trigger for capture and filtering - IRIG-B time code encoder/decoder - Ten high voltage (up to 30V) programmable DIO lines - Real-Time recording and physical bus replay - ANSI Application interface supporting C, C++, C#, and .NET development - Device driver support: Windows, Linux, & VxWorks (others on request) - Designed for extended temperature operations - 64-bit VME Interface (VME master & slave capability) - Front Panel and Rear I/O (P2) Available
-
product
1553 Avionics Interface 3U CPCI Card
QCP-1553 Series
The QCP-1553 module is a rugged, reliable, full featured, Compact PCI module designed to provide a stand-alone, MIL-STD-1553A/B interface for avionics applications. Up to four independent dual redundant MIL-STD-1553 databus streams are supported by the 3U QCP-1553 module. Additionally, the module offers full functional test, simulation, monitoring and databus analyzer functions for MILSTD-1553A/B applications. An onboard IRIG-B time code decoder and generator allows users to accurately synchronize single or multiple QCP-1553 modules to a common time source. The QCP-1553 module is available in dual or full function (RT simulation, monitoring, and bus controller) configurations.
-
product
PCI Express Interface Card
MPCIE2-1553
he MPCIE2-1553 is a mini PCI Express Full-Mini Type 2 Interface Card for 1 or 2 MIL-STD-1553 channels in an incredible small package. The MPCIE2-1553 implements the latest MIL-STD-1553 32-bit FPGA Protocol Engine Technology (AltaCore-1553) with the industry leading Multi-Layer Software development software package (AltaAPI).
-
product
Interface Module for Multimode, Multiprotocol Excalibur 8000 Family of Carrier Boards, a Complete Solution for Developing & Testing 1553 Interfaces
M8K1553Px(S)
The M8K1553Px(S) interface module for the multimode, multiprotocol, Excalibur 8000 family of carrier boards provide a complete solution for developing and testing 1553 interfaces and performing system simulation of the MIL-STD-1553 bus. The module handles all standard variations of the MIL-STD-1553 protocol.Each M8K1553Px multi function module contains 64K bytes of dual-port RAM for Data blocks, Control registers, and Look-up Tables. All Data blocks and Control registers are memory mapped, and may be accessed in real time. Each of the independent dual redundant M8K1553Px modules may be programmed to operate in one of three modes of operation: Remote Terminal, Bus Controller/Concurrent-RT, and Bus Monitor. In addition, modules 1 and 3 can be programmed to operate as Concurrent monitors, to modules 0 and 2 respectively.Each M8K1553PxS single function module operates either as a Bus Controller, Remote Terminal, or Bus Monitor.NOTE: the M8K1553PxS module is NOT compatible to the M4K1553MCH module.The M8K1553Px(S) comes complete with Windows software, a C-driver software library including source code and may be used with Exalt, Excalibur’s Analysis and Laboratory Tools, a Windows monitoring application.
-
product
Mini Munitions Store Interface
MMSI
Mini Munitions Store Interface (MMSI) (EBR 1553) modules support up to 8 MMSI hub ports and composite Bus Monitor output using the M4KMMSI module. Each module can operate in one of three modes of operation: Remote Terminal, Bus Controller/Concurrent-RT/Concurrent Monitor, and Bus Monitor.
-
product
Software
LV-1553
The LV-1553 software is the interface to operate Abaco Systems' MIL-STD-1553 USB, XMC, PCIe, PCI, cPCI, ExpressCard, PCMCIA, Q104-Plus, AMC and VME boards with National Instruments’ LabVIEW graphical programming environment.
-
product
Interface Card
XMC-1553
The XMC-1553 Interface Card and AltaAPI Represent the Latest MIL-STD-1553 32-bit FPGA Protocol Engine Technology with Multi-Layer Software. Ideal for SBCs or carriers for VPX, VME and cPCI (Compact PCI/PCIe or PXI) - Commercial or Rugged/Conduction Cooled Systems.
-
product
cPCI Intelligent Interface Card
IIB-1553-CPC
The IIB-1553-CPCI is an intelligent interface card providing full MIL-STD-1553 test, simulation and bus analysis capability for the CompactPCI bus, with 1553A, 1553B, McAir and STANAG 3838 capability on a single card.
-
product
Multi-Channel 1553 Interface for Single Lane PCI Express Systems
PCIE1L-1553
Alta Data Technologies’ PCIE1L-1553 interface module is a multi-channel (1-2), ½ size, Low Profile, One Lane PCI Express 1553 card with the latest software technologies. The PCI Express card is based on the industry’s most advanced 32-bit 1553 FPGA protocol engine, AltaCore™, and by a feature-rich application programming interface, AltaAPI™, which is a multi-layer ANSI C and Windows .NET (MSVS 2005/08/10 C++, C#, VB .NET) architecture. This package provides increased system performance and reduces integration time.
-
product
Interface Module for the Multimode, Muliprotocol Excalibur 8000 Family Carrier Boards
M8K1553MCH
The M8K1553MCH interface module for the multimode, multiprotocol, Excalibur 8000 family of carrier boards provide a complete solution for developing and testing 1553 interfaces and performing system simulation of the MIL-STD-1553 bus. The module handles all standard variations of the MIL-STD-1553 protocol.The M8K1553MCH contains 32k x 16 of dual-port RAM for Data blocks, Control registers, and Look-up tables. All Data blocks and Control registers are memorymapped and may be accessed in real time. The dual-redundant 1553 module may be programmed to operate in one of four modes of operation: Bus Controller, Remote Terminal, RT/Concurrent-Bus Monitor, and Bus Monitor. The M8K1553MCH comes complete with Windows software, and a C driver software library including source code.
-
product
PCIe-Mini Module
PCIe-Mini-1553
• Controller of dual redundant (A/B channel) 1553 communications• PCIexpress x1 Lane Interface• DDC 1553 E• SRAM 64KX16• Programmable bus controller, remote terminal, or monitor terminal modes• Multiprotocol Support of MIL-STD01553A/B Notice 2 and STANAG 3838• +3.3V Operation and Logic• On-chip transceivers/transformer• Selectable 10,12,16 or 20 MHz Systems Clocks
-
product
HS1760/MIL-STD-1760E Network Interface Controller for PCI Express
PCIe-1760-NIC-FP
Avionics Interface Technologies
Configuration Variants available: PCIe-HS1760-NCNT: One NC Node and One NT Node, PCIe-HS1760-NCNC: Two NC Nodes, PCIe-HS1760-NTNT: Two NT Nodes - SAE AS5653-Compliant Network Controller/Network Terminal NIC - Unsolicited data path for handling Fibre Channel link service or non‐FC-AE‐1553 traffic - Supports DMA for high speed streaming of data - 75 Ohm single‐ended or 150 Ohm Differential coax interface – TNC connectors - Each port supports 1.0625 Gbps speed - ANSI C API interface for both NC and NT - Device driver support: Windows, Linux, & VxWorks - Quad (4) port board available on request
-
product
Fibre Channel Simulyzer™ Products
Avionics Interface Technologies
Our Fibre Channel products support most popular avionics Upper Layer protocols including FC-AE-ASM, FC-AE-1553, FC-AE-RDMA and FC-AE-AV. All AIT Fibre Channel modules utilize multiple processors with large onboard RAM. An onboard processor runs the driver software, minimizing host CPU interaction, enabling autonomous operation with minimal interaction during time-critical applications.The Fibre Channel products use our Simulyzer™ technology that enables the hardware to simultaneously perform Fibre Channel data generation and Fibre Channel monitoring on the same physical board. The Fibre Channel test products include full-function device driver software for the most popular operating systems, an application interface supporting development environments, as well as a comprehensive set of source code examples.
-
product
Intelligent Interface Card
IIB-1553-PCI-2C
The IIB-1553-PCI-2C provides an intelligent interface card for two serial, dual redundant MIL-STD-1553 data buses and the PCI bus. The card supports 1553A, 1553B, McAir and STANAG 3838 variants on a single card. The IIB-1553-PCI-2C provides concurrent Bus Controller (BC) and up to 31 Remote Terminals (RT) with Bus Monitor (BM). An additional stand-alone Chronological Bus Monitor (CBM) facility is also provided, with comprehensive multi-level triggering capability. Full error injection capability is provided in BC and RT modes, with full error detection in BC, RT, BM and CBM modes. Two independent variable amplitude dual redundant 1553 interfaces are provided, each with2 Mbytes of dual ported RAM. The board is supplied with C drivers in source code and Windows menu driven software as standard.
-
product
Multi-Channel, Multi-Protocol 1553, ARINC, WMUX Interface for 3U PXIe
Alta Data Technologies’ PXI Express interface modules offer a wide range of MIL-STD-1553, ARINC and WMUX configuration options using Alta’s PMC cards on a single-slot PXI Express 3U carrier. The cards are based on the industry’s most advanced 32-bit FPGA protocol engines, AltaCore™, and by a feature-rich application programming interface, AltaAPI™ (with LabVIEW SDK).
-
product
Electronic Controllers
CAES designs and manufactures stepper and brushless DC controllers for aerospace applications. A variety of interfaces (1553, RS422), input voltages, and drive schemes are available. Custom requirements are welcomed.
-
product
4 Channels, MIL-STD-1553, Dual Redundant, Direct Coupled, Assisted Mode Capable (AMC)
FTF
MIL-STD-1553 is a military standard published by the United States Department of Defense that defines the mechanical, electrical, and functional characteristics of a serial data bus. It was originally designed for use with military avionics, but has also become commonly used in spacecraft On-Board-Data-Handling (OBDH) subsystems, both military and civil. It features a dual, redundant, balanced-line, physical layer; a (differential) network interface; time division multiplexing; half-duplex command/response protocol; and up to 31 remote terminals (devices).
-
product
MIL-STD-1553 A, B Simulator/Analyzer/Tester
CIC201
MIL-STD-1553 A, B Simulator/Analyzer/Tester - CIC201B VME/VXI B Size Interface, CIC201C VME/VXI C Size Interface - The CIC201 can be used for Validation Testing, Production Testing, full bus simulation and monitoring, as a general purpose 1553 interface or a stand alone bus Analyzer. For precise message scheduling and measurements, the Major and minor frame times are independent of message sequences or retransmissions on errors and the start of all command messages are independent of message length, response time or length of response. Message timing is calibrated and RT responses have low jitter.
-
product
Type 2, PCMCIA Dual Redundant MIL-STD-1553 serial bus Simulator Analyzer Tester
PC401
MIL-STD-1553 A, B, & McAir MULTI PROTOCOLS Simulator/Analyzer/Tester type 2 PCMCIA BUS Interface Card - The PC401 can be used for Validation Testing, ProductionTesting, full bus simulation and monitoring, as a generalpurpose 1553 interface or a stand alone bus Analyzer. Forprecise message scheduling and measurements, the Majorand minor frame times are independent of messagesequences or retransmissions on errors and the start of allcommand messages are independent of message length,response time or length of response. Message timing iscalibrated and RT responses have low jitter.
-
product
PXIe Avionics Interface Cards
The OmniBus II PXIe is the next-generation of Astronics' popular OmniBus product with faster I/O and processing capabilities. With the newest advanced set of MIL-STD-1553 and ARINC 429 modules, users can verify wave form compatibilities, test functions of bus shorts and opens, and—when combined with our CoPilot® software—perform lab, production and flight test verification and simulation right out of the box. Readily available as Commercial Off-The-Shelf (COTS) products, the PCIe interface is perfect for challenging simulation, test, interface, and data recording applications.
-
product
PCI Module
PCI-1553-DDC-1,2
The PCI-1553-DDC uses Data Device Corporation’s ACE, DDC enhanced mini BU61865G4-290 communication device as its 1553 bus controller, or remote terminal, or monitor terminal. A single controller has two redundant channels. This controller has 64Kx17 word of internal memory and internal transceivers for both channel A and B. The 3U PCI board has on-board transformers. This board has a PCI compliant interface
-
product
Rugged Ethernet
ES-1553RUNET/Px(S)
The ES-1553RUNET/Px is an intelligent, rugged single channel, MIL-STD-1553 adapter. Its small size and ability to interface through Ethernet interfaces make it a complete solution for developing, testing and performing system simulation of the MIL-STD-1553 bus, both in the lab and in rugged environments.The ES-1553RUNET/Px shares its API with the entire Px family so that applications currently running on PCI, PCIe, ExCARD or PCMCIA boards will run without change on this device.Multiple units can operate on the same network, by programming each one with a unique IP address, and can be accessed from any computer on the network.
-
product
4 Channels, MIL-STD-1553, Dual Redundant, Transformer Coupled, Assisted Mode Capable (AMC)
FTC
MIL-STD-1553 is a military standard published by the United States Department of Defense that defines the mechanical, electrical, and functional characteristics of a serial data bus. It was originally designed for use with military avionics, but has also become commonly used in spacecraft On-Board-Data-Handling (OBDH) subsystems, both military and civil. It features a dual, redundant, balanced-line, physical layer; a (differential) network interface; time division multiplexing; half-duplex command/response protocol; and up to 31 remote terminals (devices).
-
product
Mini PCI Card
EXC-1553mPCIe/P1
This card’s small size and suitability for Mini Card compatible computers make it a complete solution for developing, testing, integrating 1553 interfaces and for performing system simulation of the MIL-STD-1553 bus, both in the lab and in the field.
-
product
Multi-Protocol & Avionics I/O
We offer high performance, flexible, interfaces to ARINC 429, ARINC 708, ARINC 717, MIL-STD-1553 and others for a range of hosts.
-
product
CompactPCI Interface Card
CPCIC-1553/PXI
The CPCIC-1553/PXI Interface Card and AltaAPI Represent the Latest MIL-STD-1553 32-bit FPGA Protocol Engine Technology with Multi-Layer Software. Our Card and Software Packages are Designed for Fast, Portable Integrations. The CPCIC-1553 is the Only Commercial Off the Shelf (COTS) Card that Passes and Executes the SAE AS4111/4112 Protocol Tests.
-
product
Intelligent Interface Card
IIB-1553-PC104+
The IIB-1553-PC104+ is an intelligent interface card giving full MIL-STD-1553 test, simulation and bus analysis capability on the PC104+ bus, providing 1553A, 1553B, McAir and STANAG 3838 variants in a single card. The IIB-1553-PC104+ supports concurrent Bus Controller (BC) and up to 31 Remote Terminals (RT) with Bus Monitor (BM). An additional stand-alone Chronological Bus Monitor (CBM) facility is also provided, with comprehensive multi-level triggering capability. Full error injection capability is provided in BC and RT modes, with full error detection in BC, RT, BM and CBM modes. The unit provides a variable amplitude dual redundant 1553 interface. 2 Mbytes of dual ported RAM are provided. The board is supplied with C drivers in source code and Windows menu driven software as standard.
