Filter Results By:
Products
Applications
Manufacturers
1553
Interface Standard for Digital Time Division Command/Response Multiplex Data Bus
See Also: Mil-Std-1553
- Pickering Interfaces Inc.
product
PXI/PXIe MIL-STD-1553 Multiplexer, Dual 16-Channel, 2-Pole
42-739-002
The 40-739-002 (PXI) and 42-739-002 (PXIe) are dual 16-channel 2-pole multiplexers designed specifically for physical layer multiplexing or demultiplexing differential signals that conform to the MIL-STD-1553 specification. The module can be supplied as a single or dual 16-channel 2-pole multiplexer with each signal pair having a controlled 78 Ohm differential impedance.
-
product
Fibre Channel PXI Express Test & Simulation Instrument
PXIe-FC4
Avionics Interface Technologies
3U PXIe form factor will fit into any PXIe or hybrid slot - Supports Point-to-Point, Switched Fabric, and Arbitrated Loop topologies - Two independent Fibre Channel ports - Two SFP sockets accept fiber or copper transceivers - Each port supports 1, 2, and 4 Gbps speeds - Comprehensive decoding of FC-1, FC-2, and Upper Layer Protocol (ULP) frames - Triggering and Filtering - Error Injection on any Header or Payload Parameter - Data Capture to on-board memory or disk file - Live Capture and Current Value Monitoring - IRIG-B Time Code Encoder/Decoder for Data Correlation - In-line Port Configuration for Transparent Analyzer - Supports multiple ULPs including FC-AE-ASM, FC-AE-RDMA, FC-AE-1553, and FC-AV - Supports HS-1760E applications, including AS5653, AS5625, and AS5627fcXplorer Windows-based FC Simulator and Analyzer Test Software
-
product
SWaP Optimized Processing and Multifunction I/O & Communications System
NIU3A
The NIU3A is a small, rugged, low-power, self-contained processing and multifunction I/O system preconfigured with 24-CH programmable Discrete I/O, 8-CH ARINC 429/575, 4-CH CANBus and 2-CH MIL-STD-1553 functions. The NIU3A can also be configured with up to three smart Configurable Open Systems Architecture™ (COSA®) function modules. The NIU3A boasts Dual or Quad Core ARM Cortex®-A53 processors for customer software applications and I/O and communications management. The NIU3A is configured with two 10/100/1000BASE-T (GbE) Ethernet ports and an RS-232 port for maintenance / diagnostic or configuration interface. Ideally suited for rugged Mil-Aero applications, the NIU3A delivers off-the-shelf solutions that accelerate deployment of SWaP-optimized systems in air, land and sea applications.
-
product
Cable
RCONQPMC-2
RCONQPMC-2 - Transitions from a SCSI-68 pin connector to four CJ70 Twinax, 3 lug, 1553 cable jack ends and one D-Sub 50 pin connector for additional I/O.
-
product
Micsig Smart Oscilloscope
STO1000C/E
Shenzhen Micsig Instruments Co., Ltd.
*Up to 70Mpts memory depth, Zoom into a selected part of the captured waveforms to get more details. *Support serial triggering and decode (I2C, SPI, RS232/UART,CAN, LIN) and Aerospace and defence (MIL-STD 1553, ARINC 429). Two formats to display decoding, text and graphic.
-
product
1553 EBR to Ethernet Converter
ENET-1553-EBR
ENET-1553-EBR-1D™ is an innovative product that provides “remoting” of 1553 AS5652 EBR operations on 10/100/1000 Ethernet IP/UDP local area networks (LAN). ENET-1553-EBR is a small, low-power, rugged device that provides connectivity for up to eight AS5652 RT devices, single BC or composite monitor.
-
product
PMC Module
PMC-601
Curtiss-Wright Defense Solutions
The PMC-601 PMC module allows customers to incorporate MIL-STD-1553 and discrete digital I/O connectivity into military and aerospace embedded computing systems. We assure an easy integration with other elements of our product lines, as well as after-sales technical support, life-cycle management services, and the commitment to long-term availability.
-
product
PXI/PXIe MIL-STD-1553 Multiplexer, Single 16-Channel, 2-Pole
42-739-001
The modules are ideal for the testing of multiple devices that use a serial communication interface, allowing the test system to select one target device from many. The design is bi-directional to permit use as a multiplexer or de-multiplexer with no impact on performance. The module uses long lifetime electromechanical relays characterized for use in communications systems.
-
product
MIL-STD-1553 module for PCI
QPCX-1553
Abaco Systems' QPCX-1553 provides new levels of performance and flexibility for MIL-STD-1553A/B Notice II for PCI backplane form factors. Now faster, the QPCX also draws less power in a smaller board footprint.
-
product
MIL-STD-1553 & ARINC XMC Interface For SBCs, VPX, VME, CPCI/PXI Systems
XMC-MA4
The XMC-MA4’s BC capability includes variable message/label framing/subframing with transmission scheduling provides the most advanced control operations. ARINC TX has complete frequency control per channel. RT and ARINC RX, Monitor, Playback and Signal Generator functions also include industry leading functions to meet the most demanding requirements.
-
product
ISA Bus Dual Redundant MIL-STD-1553 A/B Simulator / Analyzer / Tester
CIC101-4
Price: Request QuoteMIL-STD-1553 A, B Simulator/Analyzer/Tester ISA BUS Interface Card. The CIC101 can be used for Validation Testing,Production Testing, full bus simulation and monitoring, as ageneral purpose 1553 interface or a stand alone bus Analyzer. It provides precise message scheduling andmeasurements. Major and minor frame times areindependent of message sequences or retransmissions onerrors. The start of all command messages may be set to beindependent of message length, response time or length ofresponse. The CIC101 features a calibrated Message timingand low jitter RT responses.
-
product
Wire Systems Analyzer
Console Test Systems (CTS)
Wire Systems Analyzer Commercial Roll around detects and locates faults and detects degradation in electrical interconnect systems ranging from simple to complex. Used to verify the operation of relays, circuit breakers, indicators, switches, diodes, transformers, 1553 couplers, etc.
-
product
Mini Munitions Store Interface
MMSI
Mini Munitions Store Interface (MMSI) (EBR 1553) modules support up to 8 MMSI hub ports and composite Bus Monitor output using the M4KMMSI module. Each module can operate in one of three modes of operation: Remote Terminal, Bus Controller/Concurrent-RT/Concurrent Monitor, and Bus Monitor.
-
product
8" Cable
COND25-1553
Commercial Application Transitions from a 25 pin D-sub connector on a PC expansion card end-panel to two 8" cables with CJ70 Twinax, 3 lug, 1553 cable jack ends. Military Application Transitions from a 25 pin D-sub connector on a PC expansion card end-panel to two 8" cables with CJ70 Twinax, 3 lug, 1553 cable jack ends, and two 18" cables with BNC cable jacks for I/O triggers.
-
product
IRIG 106 Chapter 10 SDK for MIL-STD-1553 Applications
Avionics Interface Technologies — A Teradyne Company LOGIN Open Search Form F-SIM-1553-AVOE F-SIM-1553-AVOE
Avionics Interface Technologies
Supports Capture, Recording, & Analysis of MIL-STD-1553 Chapter 10 Ethernet Data Streams - View Live MIL-STD-1553 Data and Activity Statistics from one or more Chapter 10 Streams - Compatible with AIT eDAQ-1553 & eDAQ-1553-FQ Modules - Open, View, Save, & Analyze MIL-STD-1553 bus data from Chapter 10 Archive Files - Replay MIL-STD-1553 bus data from Chapter 10 Archives using any of AIT’s MIL-STD-1553 Interface modules - Supported in AIT’s Flight Simulyzer simulation and analyzer software application
-
product
Fibre Channel XMC Interface Module
XMC-FC4
Avionics Interface Technologies
Supports Point-to-Point, Switched Fabric, and Arbitrated Loop topologies - Two independent Fibre Channel ports - Two SFP sockets accept fiber or copper transceivers - Each port supports 1, 2, and 4 Gbps speeds - Supports DMA for high speed streaming of data to/from the board - Full Error Injection and Detection - IRIG-B Time Code Encoder/Decoder for Data Correlation - In-line Port Configuration for Transparent AnalyzerSupports multiple ULPs including FC-AE-ASM, FC-AE-RDMA, FC-AE-1553, and FC-AV - Compatible with AIT’s fcXplorer GUI Bus Analyzer Software
-
product
Single, Dual Or Quad Stream MIL-STD-1553A/BTest And Simulation Modules For PMC
AMCX1553
MIL-STD-1553 Test and Simulation modules for PMC with 1, 2 or 4 dual redundant channels plus 8 Discrete I/O’s (on Rear-I/O).
-
product
MIL-STD-1553 Modules
> MIL-STD-1553B is the military specification defining a digital time division command/response multiplexed databus. The 1553 databus is a dual-redundant, bi-directional, Manchester II encoded databus with a high bit error reliability. All bus communications are controlled and initiated by a main bus controller. Remote terminal devices attached to the bus respond to controller commands. MIL-STD-1553B defines specifications for terminal device operation and coupling, word structure and format, messaging protocol and electrical characteristics.
-
product
Software Applications
Excalibur Systems provides software utilities and applications programs to manage data communications for our products, which include Bus Controllers, Bus Monitors, Data Recorders and analytical flight Data Reconstructors. There are different applications for single & multi function MIL-STD-1553 and ARINC-429.
-
product
PCI Intelligent Interface Card
IIB-1553-PCI
The IIB-1553-PCI is an intelligent interface card giving full MIL-STD-1553 test, simulation and bus analysis capability on the PCI bus, providing 1553A, 1553B, McAir and STANAG 3838 variants in a single card.
-
product
MIL-STD-1553 USB & LAN Test & Simulation Module
UXI-1553
Avionics Interface Technologies
Dual redundant, single, dual, or quad stream configurationsConcurrent BC, 31 RTs, and BM operations - Physical Bus ReplayFull error injection/detection capabilities - Programmable trigger and capture - Programmable Bus Coupling and Output Voltage Levels - Onboard IRIG-B time code encoder/decoder for Synchronization - Time Synchronization to IEEE 1588 via Ethernet LAN port - 10 Discrete I/O Interfaces (5 Outputs / 5 Inputs) - Operates from a single USB or Ethernet LAN connection - Supports SAE AS4112/4114 protocol testing requirements- Flight Simulyzer™ GUI Analyzer software
-
product
2 Channels, MIL-STD-1553, Dual Redundant, Direct Coupled, Assisted Mode Capable (AMC)
FTE
MIL-STD-1553 is a military standard published by the United States Department of Defense that defines the mechanical, electrical, and functional characteristics of a serial data bus. It was originally designed for use with military avionics, but has also become commonly used in spacecraft On-Board-Data-Handling (OBDH) subsystems, both military and civil. It features a dual, redundant, balanced-line, physical layer; a (differential) network interface; time division multiplexing; half-duplex command/response protocol; and up to 31 remote terminals (devices).
-
product
Express Multi Protocol Board
EXC-8000PCI
The EXC-8000PCIe is a PCI Express card supporting up to eight independent 8000 family avionics communication modules, allowing multiple different protocols to be mixed and matched on a single card. Modules available include MIL-STD-1553, MIL-STD-1760, MMSI, ARINC-429, ARINC-708, ARINC-717, Serial, Discrete and CAN bus.The EXC-8000PCIe supports extensive error injection and detection capabilities, IRIG B Time Code input, and can be ordered with an extended operating temperature range of -40ºC to +85ºC and conformal coating. The EXC-8000PCIe is supplied with C drivers, including source code.
-
product
Aerospace and Defense Software for the 4000 X-Series
D4000AERB
MIL-STD 1553 and ARINC 429 trigger and decode for the InfiniiVision 4000 X-Series oscilloscopes, along with mask testing, frequency response analysis, and video analysis
-
product
Mini PCI Module
MPCI-1553-DDC
The ALPHI MPCI-1553-DDC uses the BU-65864 communication device as its 1553 bus controller, or remote terminal, or monitor terminal. A single controller has two redundant channels and built in transceivers. The controller has internal transceivers for both channel A and B. The Mini PCI board has on-board transformers for both channels. The board format is a Mini PCI boardlayout.
-
product
1 Channel, MIL-STD-1553/1760 Communications Interface
FTJ
Based on the MIL-STD-1553 signal and interface backbone, MIL-STD-1760 defines a standardized electrical interface to address additional aircraft weapons stores management and as such, includes some special requirements. The FTJ module meets the operational requirements within the general specifications of MIL-STD-1760 as applied to an integrated I/O function module, and include special designed holt transceivers to ensure signal parameter operation and integrity.
-
product
Interface Card
XMC-1553
The XMC-1553 Interface Card and AltaAPI Represent the Latest MIL-STD-1553 32-bit FPGA Protocol Engine Technology with Multi-Layer Software. Ideal for SBCs or carriers for VPX, VME and cPCI (Compact PCI/PCIe or PXI) - Commercial or Rugged/Conduction Cooled Systems.
-
product
8" Cable
CONW1553-1
Transitions from a card end connector (with IRIG) on the QVME-1553 or QVXI-1553X into two 8" cables with CJ70 Twinax, 3 lug, 1553 cable jack ends, and four 8" cables with BNC cable jacks for I/O triggers and IRIG Rec/Gen.
-
product
ARINC 429 Simulator & Analyzer Applications Software
F-SIM-A429
Avionics Interface Technologies
Software GUI Application for Operating AIT ARINC 429 InterfacesCapture & Analyze Data from Multiple ARINC 429 Input ChannelsDefine & Execute Complex Simulations of Multiple Rate-Oriented Labels - Simulate Output Data on Multiple Channels Simultaneously - Replay Previously Captured Bus Data - Full Error Injection & Detection - Update, Modify, & View ARINC 429 Data on-the-fly - Engineering Unit Displays & Software Widgets - Receive Data to Label/SDI Specific Buffers - Also Supports MIL-STD-1553, ARINC 664, Ethernet, & Data Load operations
-
product
HS1760/MIL-STD-1760E XMC Network Interface Controller
XMC-1760-NIC-FP
Avionics Interface Technologies
Configuration Variants available: XMC-HS1760-NCNT: One NC Node and One NT Node, XMC-HS1760-NCNC: Two NC Nodes, XMC-HS1760-NTNT: Two NT Nodes - SAE AS5653-Compliant Network Controller/Network Terminal NIC - Unsolicited data path for handling Fibre Channel link service or non‐FC-AE‐1553 traffic - Supports DMA for high speed streaming of data75 Ohm single‐ended or 150 Ohm Differential coax interface – TNC connectors - Each port supports 1.0625 Gbps speed - ANSI C API interface for both NC and NT - Device driver support: Windows, Linux, & VxWorks - Quad (4) port board available on request
-
product
Multi-Channel, Multi-Protocol 1553, ARINC, WMUX Interface for 3U PXIe
Alta Data Technologies’ PXI Express interface modules offer a wide range of MIL-STD-1553, ARINC and WMUX configuration options using Alta’s PMC cards on a single-slot PXI Express 3U carrier. The cards are based on the industry’s most advanced 32-bit FPGA protocol engines, AltaCore™, and by a feature-rich application programming interface, AltaAPI™ (with LabVIEW SDK).
