Filter Results By:
Products
Applications
Manufacturers
Data Acquisition
senses the physical, represented as an analog signal, that is then converted to digital data. AKA: DAQ
See Also: Data Acquisition Systems, PCI Data Acquisition, DAQ, Digitizers
- Pickering Interfaces Inc.
product
PXI 2 Amp Multiplexer, Single 4-Channel, 8-Pole
40-635A-104
The 40-635A-104 is a single 4-channel, 8-pole MUX and is part of a range of Multiplexer modules available in 9 standard density and 9 half density configurations, all using high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC. The module is suitable for signal routing in ATE and data acquisition systems. Connections are made via a front panel 78-way D-type connector.
-
product
Modular and Scalable Multifunction Switch/Measure Units
EX1200 Series
The EX1200 product family is a modular and scalable series of multifunction switch/measure units that can be configured to address a variety of applications in the mechanical data acquisition and electronic test environments.
-
product
RS-422/RS-485 Repeater
ND-6510
ADLINK's NuDAM data acquisition modules make up a total acquisition network and control system. Up to 256 NuDAM modules an be romotely controlled on any RS-485 network from a host computer, via a single serial RS-232, allowing communication from as far as 4000 feet from the host. Based on the RS-485 multi-drop network system, each module has a unique address ID, whereby simple ASCII command & response protocols through the standard RS-485 interface can control all the NuDAM modules in the RS-485 network. The NuDAM modules provide direct communications with a wide variety of sensors, perform all signal conditioning, scaling, linearization and conversion, and can acquire measurements of temperature, pressure, flow, voltage, current, and multiple digital signal types.
-
product
Windows Driver & SDK for ADLINK PCI/PCI Express/cPCI Series Data Acquisition Cards
PCIS-DASK
ADLINK PCIS-DASK is an advanced 32-/64-bit kernel driver and 32-bit/64-bitDLL Library for custom data acquisition application development. PCIS-DASK provides a common set of Application Programming Interface (API) for ADLINK"s extensive family of PCI/PCI Express(R)/cPCI Series Data Acquisition Cards, and is ideal for custom applications development under 32-bit/64-bit Windows 7/8. With PCIS-DASK, you can easily access all functionality of ADLINK DAQ PCI/cPCI general series data acquisition cards.
-
product
16-CH 16-Bit 250 kS/s Low-Cost Multi-Function DAQ PCI Express Cards
DAQe-2213/2214
ADLINK DAQe-2213/2214 can sample up to 16 AI channels with different gain settings and scan sequences. It makes them ideal for dealing with analog signals with various input ranges and sampling speeds. These devices also offer differential mode for 8 AI channels in order to achieve maximum noise elimination.
-
product
16/32 -CH 16-Bit 250/500 KS/s Multi-Function DAQ Cards with Encoder Input
PCI-9222/9223
The ADLINK PCI-9222/PCI-9223 is a 16-bit, 16/32-CH, 250/500 KS/s high performance DAQ card with 8 different input ranges. It also features 2-CH 16-bit analog outputs capable of a 1 MS/s update rate, 2-CH encoder inputs, and programmable function I/O. The software-programmable function I/O supports a variety of applications, including TTL digital I/O, high-speed DIO, general-purpose timer/counter, pulse generation, and PWM output. Analog input, analog output, and function I/O at full speed simultaneously, and multiple cards can be synchronized through the SSI (System Synchronization Interface) bus if users need more channels than a single board can provide. Ideal for mixed-signal tests, laboratory research, and factory automation, PCI-9222/PCI-9223 is the best single-board solution on the market providing the best integration capability of multiple tasks with high performance and an affordable price.
-
product
Lan-Xi Data Acquisition Hardware
Brüel & Kjær Sound & Vibration A/S
LAN-XI modules can function individually, and can use battery power to create small, rugged, low channel count systems of up to 12 channels. You can attach many different types of front input panels to connect the transducers of your choice. Around each connector is a circular LED that shows the channel's use and health at a glance backed up with an LCD screen. A key feature is the Dyn-X technology, which avoids the need for input ranging by using dual A/D converters to ensure you get the data the first time while achieving an effective dynamic range of over 160 dB.
-
-
product
PXI 2A Multiplexer, 8-Bank, 4-Channel 4-Pole
40-614-005
The 40-614 High Density 2 Amp multiplexer module is available in 20 configurations. All configurations use high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 200VDC/140VACThe module is suitable for signal routing in ATE and data acquisition systems. User connections are made via a front panel 160-pin DIN 41612 connector which is fully supported by our range of cabling and connector solutions.
-
product
Thermographic Software
The purpose of thermography does not only implicate the acquisition of image data, it also deals with the analysis of gained measurement results putting them into practice. For this reason, InfraTec offers a wide range of efficient and user-friendly programmes for various applications and requirements. The centre of attention is, hereby, the fully scalable software family IRBIS ® 3.
-
product
USB-7856, Kintex-7 160T FPGA, 1 MS/s Multifunction Reconfigurable I/O Device
782916-01
Kintex-7 160T FPGA, 1 MS/s Multifunction Reconfigurable I/O Device - The USB‑7856 features a user-programmable FPGA for high-performance onboard processing and direct control over I/O signals for complete flexibility of system timing and synchronization. You can customize these devices with the LabVIEW FPGA Module to develop applications requiring precise timing and control such as hardware‑in‑the‑loop testing, custom protocol communication, sensor simulation, and high-speed control. The USB‑7856 features a dedicated A/D converter per channel for independent timing and triggering. This design offers specialized functionality such as multirate sampling and individual channel triggering, which are outside the capabilities of typical DAQ hardware.
-
product
6U cPCI / PXI / PXIe 6021 Full Size Chassis
The WIENER 6021 crate series can be outfitted with cPCI, PXI or PXIe backplanes to provide high performance chassis with highly reliable low-noise power supplies for these bus standards. Typical applications are data acquisition, beam line control and test instrumentation.
-
product
16-CH 12/16-Bit 100 kS/s Low-Cost Multi-Function DAQ Cards
PCI-9111 Series
ADLINK PCI-9111 series are 16-CH, 100 kS/s low cost multi-function DAQ card. The PCI-9111 series feature flexible configurations on analog inputs. A RC filter is implemented on each A/D input channel for user to attenuate or filter input signal. The PCI-9111 series provide analog inputs with 5 programmable input ranges for bipolar inputs. The PCI-9111 series also support automatic analog input scanning. PCI-9111DG provides 12-bit A/D resolution while PCI-9111HR provides 16-bit A/D resolution. The PCI-9111 series also feature 1-CH 12-bit analog output, 16-CH TTL digital inputs and 16-CH TTL digital outputs. ADLINK PCI-9111 series deliver cost-effective and reliable data acquisition capabilities, and is ideal for a broad variety of applications.
-
product
Basic Quad J-Type Analog Thermocouple Amplifier
SEN-30103-J0
Analog thermocouple amplifier board based on the AD849x from Analog Devices (successor of the AD597). This quad-channel thermocouple board converts the very low voltage signal from a thermocouple to a highly-linear, 0.005V/C output with either 0V or 1.245V offset (both configurations stocked) while removing unwanted noise from the signal. Many supply and output configurations are available with this board, though the PCB was designed with Arduino in mind. Specifically, the output header will plug directly into a standard Arduino Uno or Mega, with a pin-for-pin match for power supply, ground and analog outputs. With a 5V Arduino, temperatures from 0C to 1,000C are possible with the 0V offset board and -249C to 750C with the 1.245V offset board. If using a 3.3V microcontroller (Due, etc), the board must be supplied with no more than 3.3V to avoid damaging the microcontroller. Temperature measurement range is dependent on the supply voltage. It is possible to supply the board with higher voltages to allow temperature measurement over the entire operating range of the K-Type and J-Type thermocouples, allowing use with more capable data acquisition equipment.
-
product
Ethernet/LXI hybridNETBOX 16 Bit Digitizer and AWG - 40 MS/s on 2 DAQ Channels and 2 AWG Channels
DN2.813-02
The hybridNETBOX DN2.80/81x series internally consists of a Digitizer and an AWG that can run together or independently. That allows simultaneous data generation and data acquisition for stimulus-response tests, ATE applications, MIMO applications or closed-loop applications. Used independently, the digitizer can acquire test data in the field and the AWG can replay this test data in lab. The hybridNETBOX offers 16 bit resolution and is available with sampling rates of 40 MS/s and 125 MS/s. The hybridNETBOX can be installed anywhere in the company LAN and can be remotely controlled from a host PC.
-
product
Integration
Aegis Industrial Software Corp.
MES cannot exist as an information island. Other systems such as ERP, time and attendance, PLM and factory and warehouse equipment all benefit from MES data and vice versa. To ensure efficient connection to the enterprise, FactoryLogix offers the most integratable architecture and options available. Business system integration via an Service-based API, programmatic data export for basic integrations, and standards-based machine data acquisition to connect the factory assets to the system.
-
product
Data Acquisition DSP Based 16 Channel
CPCI-AD8-opt8
The CPCI-AD8/16 module provides a 3U high performance data acquisition subsystem. There are (8) eight or (16) sixteen 100/200 KSPS ADC’s for maximum performance. The Local DSP can be used to simply move data samples to the CPCI bus or can provide processing functions such as limit checking, FFT’s, digital filtering, etc. Software can be downloaded to the DSP via the CPCI interface.
-
product
PXIe 8 Bit High Speed Digitizer - 1.25 GS/s on 4 Channels, 500 MHz Bandwidth
M4X.2212-X4
The 9 models of the M4x.22xx-x4 Express series are designed for the high speed data acquisition. Each of the input channels has its own A/D converter and its own programmable input amplifier. This allows the recording of signals simultaneously on all channels without any phase delay between them. The extremely large on-board memory allows long time recording even with the highest sampling rates.
-
product
Wireless IoT Solutions, Modules & I/O Board
Advantech provides simple, scalable, efficient transmit features for Wireless IoT Solutions using accurate data acquisition and secure connectivity.
-
product
PC/104 Integrations
Sundance Multiprocessor Technology Ltd.
Listed below are our PC/104 based COTS integrations.We have products with ADC, DAC, DAQ video etc.
-
product
Software & Utilities
Supports ADLINK PCI Express, PCI, PXI, USB DAQ devices and PXI controller, chassis, bus expansion modules, and edge platform.
-
product
PXI Very High Density MUX 49 Chan 4 Pole
40-675-002-49/4
The 40-675 series of very high density low cost multiplexer modules are available in a versatile range of switching configurations. The modules are supplied pre-configured in one of six multiplexer modes suitable for signal routing in high channel count ATE and data acquisition systems. The modules use high quality electromechanical signal relays allowing each channel to switch current up to 1A at 150VDC/100VAC. Connections are made via a front panel 200-pin connector.
-
product
IPEmotion Software
On-the-spot measurement and reliable data acquisitionare our primary focus. That is why we have developed IPEmotion – an intuitive and easy-to-use configuration and data acquisition software. IPEmotion connects complex ECU applications with highlyprecise measurement instrumentation. By offering special PlugIns, the program supports all measurement applications in automotive testing, regardless of the hardware in use. Customized OEM setups and installations provide you with a tailored software solution for your development process.In addition to that, IPEmotion supports online adjustmentsto your measurement screen while storing data. IPEmotion is available in several languages and permits the acquisition of large data volumes as well as automatic evaluation, reporting and offline processing of measurement data.
-
product
Portable Data Acquisition & Analysis System
LapCAT III
# 4, 8, or 16 channels# 1 MHz aggregate 12 bit sampling. Resolution is 0.024% of full scale# 13 recording durations, user selected: 132 msec to 1320 sec# Digital Triggering from any channel, with +/- slope or window# 6 full scale gain ranges, user selected: 0.4, 1, 2, 4, 10, and 20 volts full scale - with a 10mV/g accelerometer these equal 40g, 100g, 200g, 400g 1000g and 2000g full scale - higher or lower ranges by different sensor selection
-
product
PXI 5 Banks of 16 Channel 1 Pole MUX
40-615-021-5/16/1
High density multiplexer modules featuring a wide range of switching configurations, especially useful where a large number of small multiplexers are required. Typical applications include signal routing in ATE and data acquisition systems. Each module is factory configured into one of the configuration modes. Connections are made via a front panel 200-pin connector.
-
product
Analog Multiplexer Board
104-AIM-32 PC/104
The 104-AIM-32 is an analog signal multiplexer conforming to the PC/104 standard. The card will multiplex and condition 16 differential or 32 single-ended analog signals before passing them to an analog-to-digital converter card like the 104-AIO12-8. A system may comprise one to seven of these cards in tandem with one 104-AIO12-8 A/D converter board. The 104-AIM-32 card may be used as part of a large data acquisition system. The 104-AIM-32A Kit consists of one 104-AIM-32 and one 12-bit 8-input A/D board.
-
product
System Integration
G Systems develops fully integrated systems and we know that both software and hardware are equally important to system design. Our focus on code quality and optimization ensures customers receive efficient and maintainable code. We specialize in LabVIEW development and all of our LabVIEW developers are certified developers or architects. We’re also highly skilled in mechanical and electrical hardware design and builds on a wide variety of data acquisition, signal conditioning, RF, and distributed communication platforms.
-
product
IC-3120, 1.91 GHz Intel Atom Quad-Core Processor, 2-GigE Port Industrial Controller
784959-01
The IC‑3120 is a compact and rugged industrial controller that withstands the harsh environments common in automation, supervisory control, distributed control, and industrial embedded OEM applications. The IC‑3120 offers two Gigabit Ethernet ports with Power over Ethernet (PoE) technology, FPGA-based I/O capabilities, and network connectivity for distributed control applications. The advanced features include the ability to synchronize image inspection results with industrial I/O and configure hardware-timed network triggers to trigger camera acquisition, motion control, or data acquisition. You can use the advanced FPGA personality that is shipped with the system or customize the FPGA functionality using the LabVIEW FPGA Module.
-
product
High Intensity Pulsed Solar Simulator
GEN 2
Alpha-Omega Power Technologies, LLC.
The GEN 2 pulsed solar simulator and data acquisition systems can generate over 1,200 suns with a spot size of 12 mm x 12 mm at a rate of 2 pulses per second.
-
product
SH68M-68M-EPM, Male 68 pin SCSI to 68 pin VHDCI, 0.3m
192288-0R3
68-Pin Male VHDCI to 68-Pin Male VHDCI, Twisted Pair, Shielded Multifunction Cable - The SH68M-68M-EPM Cable, sometimes referred to as SHC68-C68-EPM, connects DAQ devices. The cable includes separate digital and analog sections, individually shielded twisted pairs for analog inputs, individually shielded analog outputs, and twisted pairs for critical digital I/O. The SH68M-68M-EPM Cable is offered in different lengths.
-
product
Measurement Software
Measurement Software – Comfortable software solutions from MCD allow the user an efficient acquisition and evaluation of specific test data. Especially in the audio and video analysis areas they are most often the cheaper solution to expensive hardware.
