Filter Results By:
Products
Applications
Manufacturers
Power Network Analyzers
Breakdown electrical network elements to examination.
See Also: Network Analyzers, Vector Network Analyzers, Electrical Network Analyzers, Optical Network Analyzers, Portable Network Analyzers, Radio Network Analyzers, Scalar Network Analyzers, Wireless Network Analyzers
- Pickering Interfaces Inc.
product
PXI/PXIe Power Relay Module, 18xSPST, 5 Amp, 50-pin SGMC Connector, With Interlock
42-153-004-HI
The 40/42-153-004-HI is a PXI/PXIe high density power relay module with 18xSPST switches rated at 5A and includes the hardware interlock option. User connection is via a 50-pin SGMC male connector, hardware interlock is via a 4-pin 00 series socket (mating plug is supplied).
-
product
Power Splitter, DC to 18 GHz
11667A
The Keysight 11667A power splitter is recommended when making wideband ratio measurements using a Keysight 8757 scalar network analyzer. This two-resistor type power splitter provides excellent output SWR at the auxilliary arm when used for source leveling or ratio measurement applications. The tracking between output arms over a frequency range from dc to 18 GHz allows wideband measurements to be made with a minimum of uncertainty.
-
product
Amplifier, Switch and Test Box
CLIOQC Model V
The QCBOX Model 5 is a non-conventional unit designed to fulfil actual and future needs of an electro-acoustical analyzer like the CLIO system. It is USB linked to a PC and can be configured, with dedicated software controls, to assist frequency response and impedance measurements or to perform DC measurements. Using it for frequency response measurements acts as 50W power amplifier to drive the speaker or network under test while routing one-of-four inputs to the analyzer as well the current sensing output. The four inputs are able to provide a phantom power supply both for Audiomatica or general purpose microphones (0-24 V range, software controlled). Impedance measurements can be done either switching the D.U.T.’s load across the analyzer’s input or using a dedicated output, ISENSE, thus allowing impedance measurements in constant voltage mode as well voice coil current distortion analysis. An internal ADC measures the DC current into the voice coil. Thanks to an internal software controlled voltage generator the speaker can be driven with a superimposed DC voltage (±20V), allowing for measurements of large signal parameters. Two ADC converters with a ±2.5 V and ±5 V are available at inputs 3 and 4 to measure the displacement with a laser sensor or any other DC signal. A dedicated digital input handles an external foot pedal switch (or TTL signal) to be connected and triggers QC operations. A 6 bit output – 5 bit input TTL digital port is available to interface the QCBOX and driving software with external hardware (like turntables for example).The QCBOX Model 5 finds use both in laboratory for R&D applications and in production lines setups.
-
product
POLAR ENERGY
4BAAA
Polar Energy (the successor of the Elcontrol VIP 396 energy analyzer) is a multifunctional panel (96 x 96 mm) mounted tool, ideal for remote measurement, display and remote monitoring of electrical quantities.It features a 128×128 graphic display of great visibility and comfortable frontal buttons for direct consultation and setup. It has a wide range of electrical measurements.Compared to the predecessor VIP396, it adds many functionalities that make Polar Energy a modern and user-friendly tool for the user such as the introduction of cyclic connection verification to make installation easy and secure.The connections to the power cables and to the cables of the voltages and currents are carried out via the 2.5 mm2 terminals in the back of the instrument.For the calibration of the currents, it is necessary to use three TAs with a secondary 5 A.It can be used on single-phase, two-phase, three-phase low and medium voltage networks. Advanced features and included analysis software make it an ideal tool for the most demanding professional needs.
-
product
4-Port 20 GHz Analyzer, Direct Receiver Access
C2420
C2420 Vector Network Analyzer delivers industry-leading dynamic range and sweep speed, with all the features engineers have come to expect included standard in our software. The C2420 network analyzer has direct receiver access for special applications involving external directional coupling, including Load Pull and high power measurements.
-
product
K-50 Series Probes
The K-50 coaxial probe provides an instrumentation-quality interface for broadband R.F. measurements up to 4 GHz. With the K-50 R. F. circuit design, impedance characterization measurements can be performed using it as a Network Analyzer port-extending accessory. Accurate and repeatable small signal and R.F. power (50 Watts) measurements provide consistent and repeatable results.
-
product
System Controllers
Kratos Defense & Security Solutions, Inc.
- Precise and accurate six-axis tracking control- An easy-to-use graphical user interface accessible from anywhere on the network- Optional integrated control capabilities and hardware, such as an integrated spectrum analyzer, beacon receiver, uplink power control, auto acquisition, carrier monitoring & logging, and much more
-
product
Active Hot Parameters
S93110B
S93110B active hot parameters is available on PNA-X Series network analyzers (N524xB) and provides more accurate method to test hot S-parameters, gain and output power, etc. than traditional methods by utilizing X-parameter technologies.
-
product
Power Limiter, DC to 6 GHz, APC-7
11930A
The Keysight 11930A limiter provides input protection for a variety of RF and microwave instrumentation. For example, the input circuits of network analyzers may be protected for inputs up to 6 watts peak or 3 watts average power using the Keysight 11930A.
-
product
Lightwave Detector
N4377A
The N4377A Lightwave Detector is a USB-powered optical-electrical converter with built-in optical power meter capability. If used with a vector network analyzer or a spectrum analyzer it enables frequency domain applications in photonics.
-
product
Portable Power Analyzers
Portable network analyzers are essential for conducting energy audits as well as for reviewing the quality of the power supplied and the consumption in electrical installations. They provide for real-time recording and monitoring of electrical parameters, anywhere in an electrical installation, for the conduct of energy improvement studies, as well as for the detection of problems related to the quality of supply and consumption.
-
product
Power Limiter, 0.01 to 18 GHz
N9355B
The N9355B power limiter provides the best broadband input power protection to sensitive RF and microwave instruments and components, like network analyzers, spectrum analyzers, and amplifiers, from excess RF power, DC transients and ESD. Minimize your measurement uncertainty and improve your measurement accuracy with the limiter's superior RF performance.
-
product
Battery Analyzers for Stationary Battery Systems
Fluke Battery Analyzers are the ideal test tool for maintaining, troubleshooting and performance testing individual stationary batteries and battery banks used in critical battery back-up applications in data centers, telecom networks, power distribution systems and more. With an intuitive user interface, a compact design, and rugged construction the Fluke Battery Analyzers are designed to provide optimum performance, test results and reliability.
-
product
Power Quality Analyzer
PQM-703
Power quality analyzer PQM- 703 is a technically advanced product that allows for comprehensive measurements of the quality of electricity , analysis and recording of power network parameters, for frequencies 50/60 Hz in accordance with European standard EN 50160. PQM -703 is another representative of a well, known family of analyzers line PQM- 70x . In relation to the PQM -702 has new functions like recording of transients with max. sampling frequency 10 MHz (rapid changes in voltage) and control signals. Minimal transient capturing time is 650 ns. It is intended for a very wide range of users who need to control the quality of power with a mobile device , which fulfills the requirements of a multi-sheet standard IEC 61000 for class A analyzers. This applies to measurement accuracy, measurement methods, and synchronization of time with a standard signal. The last condition is met with a built-in GPS module with an internal antenna. If the analyzer is installed inside, it is possible to use an additional antenna with a 10m-long wire. If the antenna is situated outside, GPS signal will be attainable without any problems and used for the synchronization of an internal clock.
-
product
Active Hot Parameters For E5081A ENA-X And E5080B ENA
S96111B
The S96111B active hot parameters are available on ENA-X or ENA network analyzers and provide a more accurate method to test hot S-parameters, gain and output power than traditional methods by utilizing X-parameter technologies. Restricted to 50 GHz.
-
product
Power Divider, DC to 26.5 GHz
11636B
The Keysight 11636B is a dc to 26.5 GHz power divider for direct power dividing applications. The excellent impedance match of all three ports improves fault location measurements by reducing re-reflections. The Keysight 11636B power divider/combiner is recommended when making wideband comparison measurements with the Keysight 8757 scalar vector network analyzer.
-
product
Active Differential Probe, 100 kHz to 12 GHz
U1818B
The Keysight U1818B 100 kHz to 12 GHz active differential probe makes it easy to perform high frequency in-circuit measurements using network, spectrum and signal source analyzers. With flat frequency response, low noise floor, and direct power from instrument connection, the U1818B allows measurements to be made while taking full advantage of Keysight's RF analyzers dynamic range.
-
product
Noise Receiver Modules And Noise Switching Modules
MT7553 Series
Noise Parameters are the non-50Ω extensions of Noise Figure, and are an important modeling and model validation tool to understand how a device-undertest’s performance changes as a function of source impedance. Noise Parameter measurements are typically performedusing a Vector Network Analyzer (VNA) to measure the S-Parameters of the DUT, and a Noise Analyzer (either Noise Figure Analyzer NFA or Spectrum Analyzer SA) to measure the noise power of the DUT. Noise parameters are calculated from a combination of knownsource impedances, S-parameters and noise powers.
-
product
Power Limiter, 0.01 to 50 GHz
N9355F
The N9355F power limiter provides the best broadband input power protection to sensitive RF and microwave instruments and components, like network analyzers, spectrum analyzers, and amplifiers, from excess RF power, DC transients and ESD. Minimize your measurement uncertainty and improve your measurement accuracy with the limiter's superior RF performance.
-
product
Power Quality Analyzer
PQM-700
*power to the analyzer is supplied from tested mains (internal power supply) and is used in all types of networks from 64 V to 760 V, with particular emphasis on measurements at low voltage poles, due to the ease of connection,*has an independent power supply socket, especially suited for voltage measurements for transformers and DC circuits,built-in real-time clock.
-
product
Power Splitter, DC to 26.5 GHz
11667B
The Keysight 11667B power splitter is recommended when making wideband ratio measurements using a Keysight 8757 scalar network analyzer. This two-resistor type power splitter provides excellent output SWR at the auxilliary arm when used for source leveling or ratio measurement applications. The tracking between output arms over a frequency range from dc to 26.5 GHz allows wideband measurements to be made with a minimum of uncertainty.
-
product
VNA & SWR Site Analyzers
6050
SWR Site Analyzer with VSWR, Return Loss and FDR (Frequency Domain Reflectometer) measurements. VNA Site Analyzer with full Vector Network Analyzer measurement suite S11 and S21 ports, Spectrum Analyzer, Power Meter and FDR (Frequency Domain Reflectometer) measurements. Quickly shift between VNA and SWR/Return Loss only.
-
product
Active Hot Parameters For M98xxA PXIe VNA
S95111B
S95111B active hot parameters are available on M98xxA PXIe vector network analyzers and provide a more accurate method to test hot S-parameters, gain, and output power than traditional methods by utilizing X-parameter technologies. Restricted to 50 GHz.
-
product
Harmonic/Flicker Analyzer for IEC61000-3-2/3/11/12, IEC61000-4/7/15
KHA3000
KHA3000, in addition to the complied standards and features of the KHA1000 (dedicated for single phase), is equipped for the harmonic and flicker compliance test exceeding 16A of the single-phase and three-phase equipment. With this unit alone, you can take highly accurate simultaneous three-phase measurements up to 40A/phase*. Furthermore, the KHA series is compliant with two measurement technique standards, the existing and the latest versions, so you can simply select to take measurements for the latest standard including interharmonics and for the conventional integral multiple harmonics without using any other device. In addition to the real-time display that can be used like an oscilloscope and FFT analyzer, the unit offers the real-time judgment of compliance with standards. Using this unit alone, you can judge test results and prepare result reports without the use of a PC. On top of that, you can easily set up a test system by combining KHA3000 with an AC power supply (PCR-LA Series) and a line impedance network (LIN40MA-PCR-L).
-
product
Power Quality Analyzers
Power quality analyzers designed for monitoring all electric parameters on single and three-phase installations. An in-depth verification of electric networks operation allows optimizing and increasing the efficiency of installations and reducing consumption and costs. The innovations designed and realized by HT are exporting the made in Italy style all over the world also in this sector.
-
product
FieldFox Handheld Analyzer Software
FieldFox can be configured as a cable and antenna analyzer, vector network analyzer, spectrum analyzer, built-in power meter and much more using software/firmware functionality. All functions listed on this page can be installed at the time of FieldFox purchase or can be upgrade via a software license key. Select the functionality you need today and add more features as your needs change.
-
product
Frequency Expansion Modules
bsw TestSystems & Consulting AG
Up To 1.5THz For Network Analyzers Modern communication standards, like for instance 5G, place high demands on components (mixers, amplifiers, antennas, etc.), which have to be examined in high frequency bands (millimeter waves); the requirements include: broad frequency coverage, sufficient output power to operate the components under compression, high dynamic range and stability as well as a reduced dynamic content within the spectrum.
-
product
Power Analyzers
At PCE Instruments you will find a power quality analyzer to measure the power in W, kWh or to analyze and measure harmonics. This power analyzer is a multi-function power analyzer device that measure precisely direct current, alternating current, AC-voltage, DC-voltage the intensity of DC or AC, phase rotation and idle, apparent and effective power. The reading of AC power is considered the real value and has a maximum range of 6000 Watts. While a reading is being taken, the polarity changes automatically, if negative values are taken then a minus sign will appear on the device display.Nowadays, power quality analyzers have many features such as, insulated current input, measurement of harmonics, AC and DC current measurement, AC and DC voltage measurement, frequency measurement, phase rotation measurement and idle, apparent and effective power measurement. All this data can also be logged and analyzed with the delivered PC-Software. Power analyzers of the type PCE PA 6000 can determine the energy in single-phase systems.Power quality analyzers of type PCE-GPA 62 allow the energy measurement in symmetrically loaded three-phase systems. Power analyzers of type PCE-PA 8000, PCE-360 and PCE-830 support professional power and energy measurements in single and three-phase systems.Apart from being used as energy-measuring devices, power analyzers like the PCE-830 can also be used for network analysis and the determination of harmonics and phase rotation. On our website you will find other power analyzers used in the field of electronics.
-
product
Injection Transformer
J2100A
The injection transformer is presently the prevalent method for connecting the network analyzer to the circuit being tested, and is primarily used for control loop stability measurements. The goal of the transformer is to inject a signal into the control loop being measured, without impacting the performance of the loop. In order to accomplish this to a reasonable degree, The transformer is isolated and therefore is capable of floating on a high voltage, such as a Power Factor Corrector (PFC), which is often close to 400VDC. Measuring voltages that exceed the voltage rating of the FRA inputs require attenuation probes.
-
product
WIFI Converter
When MRC meter with RS232 interface is connected to RSW-914, the meter can share data via WiFi technology. Therefore, personal devices, like desktop, laptop, smart phone, tablet... with WiFi function can be read the measuring data via WiFi. For example if factory installs Power analyzer DW-6095 along with RSW-914, then operator can monitor the power information (measuring value ) via WiFi network with safety.
-
product
Power Limiters
Keysight's power limiters provide the best broadband input protection from excess RF power, DC transients and ESD, for a variety of RF and microwave instruments and components. For example, the input circuitry of spectrum analyzers, network analyzers, frequency counters or amplifiers can be protected from unintentional inputs up to 5 watts average power. At even greater power levels, failure mode for the limiter is either an open circuit or a short circuit to ground, thereby protecting the instrument from damage.