Filter Results By:
Products
Applications
Manufacturers
Attenuators
Reduces the amplitude of a signal without appreciably distorting its waveform.
See Also: Filters, Circulators
- Pickering Interfaces Inc.
product
PXI/PXIe Solid State Attenuator, Triple, 6GHz, 50Ω, SMA
43-182B-003
The 41-182B-003 (PXI) and 43-182B-003 (PXIe) are programmable RF attenuator modules with 3 channels in one slot capable of inserting a signal loss of 0 to 31.75dB in 0.25dB steps. The attenuators use solid state switches for a long service life and fast operation with minimum settling time and no signal bounce.
-
product
POWER ATTENUATORS
TYPE ATF
National RF’s Type ATF Power Attenuators were designed to allow interfacing of linear power amplifiers to RF exciters, where a specific amount of drive to the amplifier is prescribed. Often, however, drive from the RF exciter exceeds this minimum prescribed level and some form of power attenuation must be used in order to not damage the input of the power amplifier. National RF’s type ATF-3 offers 3 dB of power attenuation (1/2 of the power) when used between the exciter and the amplifier and will handle an input power of 132 Watts, RMS (continuous power) while providing about 66 Watts RMS output power, when it is terminated into 50 ohms. In practice, the ATF-3 attenuator will handle exciters achieving Peak Envelope Power levels (PEP) in the area of 200 to 250 Watts while providing half of that power to the load. For less attenuation requirements, the ATF-1 and ATF-2 offer 1 and 2 dB of attenuation, respectively.
-
product
Voltage Variable Attenuators
Voltage variable attenuators (VVAs) that offer up to 60 dB of attenuation across a broad range of frequencies from 400 MHz to 18 GHz. These voltage variable attenuators are frequently used in applications such as electronic warfare, instrumentation, point-to-point and point-to-multipoint radios, fiber optic and broadband telecom, microwave radio and VSAT, military radios, radar, ECM, SATCOM and sensors, and R&D.
-
product
6, 8 GHz, 4 Channel Programmable Attentuator
QPA8, PA8
This device has low impedance mismatch, high bandwidth, wide dynamic range and is capable of rapid state change. The QPA8 can be an attractive alternative to either the manually operated microwave attenuator switches, which are expensive and are switched very slowly, or the relay attenuators which are expensive and wear out quickly. Attenuation is controlled in standard steps of 0.0625 dB. The 10 bit programmable range results in the full 210=1024 steps yielding a dynamic range of 0 to 63.9375dB. Non-standard custom step sizes are available.
-
product
Chassis - Controls up to 16 8x1 Modules, 32 4x1 Modules or Mixtures or 8x1's, 4x1's, 2x1's and 2x2 Modules in Any Combination or Configuration up for up to 128 Relay Drives
CXM/128-MF
These Chassis controls up to 16 8x1 modules, 32 4x1 modules or mixtures of 8x1"s, 4x1"s, 2x1"s and 2x2 modules in any combination or configuration for up to 128 relay drives. LEDs on the front panel show switch and power status. Add Switch Modules, display / driver modules and a Control Module to complete the system or simply buy the chassis wired out to D connectors to control your own relays. A manual control is optional. Chassis is available with sink or source relay drivers from + 5 to + 28 volts, ot TTL drivers for programmable attenuators. Firmware commands for Fade and Handover for WiFi, Cell Phone and WiMax labs. Fully custom systems built with little to no NRE.
-
product
Adapter/Stainless Steel
WADP-NMSF-01
Warison provides wide range of wireless passive coaxial components, includes Adapters, Attenuators, Coaxial Cables Assemblies, DC Blocks, Filters, Isolators & Circulators, Probes & Terminations. With outstanding capability of development and design, Warison is able to custom the spec based on customer��s demand. All Warison��s products pass inspection and electronic performance test before shipping out. It is our principal to deliver the best solution to all our clients.
-
product
Passive Optical Components
Wuhan Sunma Technology Co., Ltd.
Passive Optical Components are the foundation stone of WDM Passive Optical Network (PON). Besides MUX/DEMUX and splitters, SunmaFiber also provides other passive optical components such as attenuators, circulators, collimators, and isolators etc. In addition, we offer Customized Service that products with various parameters can be designed to meet different requirements. With very high performance but lowest prices on the market, our passive optical components can be the most cost-effective solution for modern PON systems.
-
product
Coaxial Programmable Attenuators
Coaxial attenuators are constructed with passivated stainless steel for durable use in both engineering labs and production line environments. These coaxial attenuators are designed and manufactured for low VSWR, low insertion loss and high attenuation value accuracy. The standard offering covers the frequency range of DC to 110 GHz and includes various interface options from 2.4 mm to 1 mm connector types as well as both male and female interfaces. The power handling of standard models is 0.5 to 1 watt continuous wave (CW). Higher power handling levels and different attenuation values and connector types from those listed below can also be requested.
-
product
Attenuators
Keysight Attenuators offer a compact, rugged design with exceptionally low insertion loss. Our latest design evolution sets new standards for size and performance. Keysight Attenuators provide excellent repeatability and safeguard your test platform from failures, downtime, and lost production. Discover which of our Attenuators best suits your test and measurement needs.
-
product
Adapter/Stainless Steel
WADP-SFSF-01
Warison provides wide range of wireless passive coaxial components, includes Adapters, Attenuators, Coaxial Cables Assemblies, DC Blocks, Filters, Isolators & Circulators, Probes & Terminations. With outstanding capability of development and design, Warison is able to custom the spec based on customer��s demand. All Warison��s products pass inspection and electronic performance test before shipping out. It is our principal to deliver the best solution to all our clients.
-
product
Waveguide Variable Attenuators
A variable attenuator from Pasternack. This SMA microwave attenuator is a continuously variable attenuator design.
-
product
Flexible Cable Assembly
WCBA-WC0129M.29M1
Warison provides wide range of wireless passive coaxial components, includes Adapters, Attenuators, Coaxial Cables Assemblies, DC Blocks, Filters, Isolators & Circulators, Probes & Terminations. With outstanding capability of development and design, Warison is able to custom the spec based on customer��s demand. All Warison��s products pass inspection and electronic performance test before shipping out. It is our principal to deliver the best solution to all our clients.
-
product
Attenuators
The 01311 attenuator chip series is designed to achieve precision and tight flatness with an attenuation accuracy of ± 0.2 dB on our 1-10 dB pads and ± 0.3 dB on our 11-20 dB pads. SemiGen tests 100% of all attenuator chips prior to shipment to verify that they meet specifications.
-
-
product
Attenuators
An attenuator is an electronic device that reduces the power of a signal without appreciably distorting its waveform.
-
product
PXI Dual RF Attenuator, 2.3GHz
41-181-022
The 41-181 Programmable Attenuator Module is available with either one or two independently programmable attenuators in a single width 3U PXI module. Each attenuator uses high reliability mechanical switches to operate binary weight attenuator pads, providing attenuation values from 0 to 63dB in 1dB steps. Attenuator operating time is typically just 5ms, ensuring fast setting times.
-
product
Adapter/Stainless Steel
WADP-QSMSF-01
Warison provides wide range of wireless passive coaxial components, includes Adapters, Attenuators, Coaxial Cables Assemblies, DC Blocks, Filters, Isolators & Circulators, Probes & Terminations. With outstanding capability of development and design, Warison is able to custom the spec based on customer��s demand. All Warison��s products pass inspection and electronic performance test before shipping out. It is our principal to deliver the best solution to all our clients.
-
-
product
Voltage Variable Attenuators
a High Reliability Low Noise Voltage Controlled Oscillator (VCO) which covers a 10 MHz to 20 MHzfrequency band with a voltage tuning range from 0V to 20V. This design features exceptional phase noise performance of -120dBc/Hz @ 10 kHz offset. Supply Voltage is +15V with a generated output power level of +10 dBm and 2nd harmonic output of-11 dBc typical. The assembly is RoHs compliant and available in a compact 0.5 inch SMT package with an industry standardmounting footprint. The bottom surface is copper clad with 2-5 micro inches of immersion Gold over 150 - 250 micro inchesof Electro less Nickel which makes it resistant to oxidation for ease of soldering. The VCO operates over a temperature rangeof -40°C to +85°C and is designed to meet a variety of MIL-STD-202 test conditions including Humidity, Shock, and Vibration.
-
product
LXI And LXI/USB Modular Chassis
Our LXI modular chassis are available in 7 and 18-slot and our LXI/USB modular chassis are available in 2, 4 and 6-slot and support over 1,000 of our PXI modules. The PXI modules supported range from: PXI general purpose relays, matrices, multiplexers and RF switches to special PXI switching functions such as fault/signal insertion. Also supported are a selection of simulation modules such as programmable resistors, digital I/O, power supplies, thermocouple simulators, function generator, battery simulators and attenuators. This gives you enormous flexibility to define a switching or T&M system to exactly match your needs.
-
product
Digital Phase Shifter
Analog Devices digital phase shifters change the phase of RF, microwave, or millimeter wave signals while providing no amplitude change. They are used in a variety of applications, including RF PA linearization/RF distortion, amplitude and phase modulation, variable attenuators, and fiber optics.
-
product
LXI Modular Chassis
Our LXI modular chassis are available in 7-slot or 18-slot and support over 1,000 of our PXI modules, additionally our 2-Slot USB/LXI Chassis allows most of our 1 or 2-slot PXI modules to be controlled via USB or Ethernet. These range from: PXI general purpose relays, matrices, multiplexers and RF switches to special PXI switching functions such as fault/signal insertion. Also supported are a selection of T&M modules such as programmable resistors, digital I/O, power supplies, battery simulators and attenuators.
-
product
Millimeter Wave Control Devices
Ducommun millimeter wave products include various control devices for system integration. The CAE, CPS, CPD and CPM series control devices are discrete or MMIC based PIN diode attenuators and switches. The CAF, CAL, CAR and CPL series control devices are waveguide based mechanical tunable attenuators and phase shifters. These devices are offered to cover the frequency range from 18 GHz to 110 GHz.
-
product
Cable Diagnosis System
Baseline 9400 TDR/ICE
K&S Engineering and Scientific Ltd
BASELINE 9400 TDR/ICE - the unique cable diagnostic system: - A state-of-the art cable fault locating instrument containing a high speed data recorder, capable of capturing and evaluating 40 million samples of electrical data per second, while also featuring amplifiers, attenuators and an adjustable pulse generator.
-
product
PXI Attenuator/Switch Driver Module
M9170A
The Keysight M9170A is a one-slot PXI attenuator switch driver module that provides the flexibility to drive Keysight's expansive portfolio of RF & microwave step attenuators and electromechanical switches. It is a PXI-hybrid compliant module that comes with a full-featured graphical interface soft front panel for easy control and trigger.
-
product
Adapter/Stainless Steel
WADP-24FSF
Warison provides wide range of wireless passive coaxial components, includes Adapters, Attenuators, Coaxial Cables Assemblies, DC Blocks, Filters, Isolators & Circulators, Probes & Terminations. With outstanding capability of development and design, Warison is able to custom the spec based on customer��s demand. All Warison��s products pass inspection and electronic performance test before shipping out. It is our principal to deliver the best solution to all our clients.
-
product
Adapter/Stainless Steel
WADP-24F35F
Warison provides wide range of wireless passive coaxial components, includes Adapters, Attenuators, Coaxial Cables Assemblies, DC Blocks, Filters, Isolators & Circulators, Probes & Terminations. With outstanding capability of development and design, Warison is able to custom the spec based on customer��s demand. All Warison��s products pass inspection and electronic performance test before shipping out. It is our principal to deliver the best solution to all our clients.
-
product
Flexible Cable Assembly
WCBA-WC03SM.SM1
Warison provides wide range of wireless passive coaxial components, includes Adapters, Attenuators, Coaxial Cables Assemblies, DC Blocks, Filters, Isolators & Circulators, Probes & Terminations. With outstanding capability of development and design, Warison is able to custom the spec based on customer��s demand. All Warison��s products pass inspection and electronic performance test before shipping out. It is our principal to deliver the best solution to all our clients.
-
-
product
Variable Attenuators
Variable attenuators are an integral part of most BER testing and EDFA characterization setups. All of EXFO's modular (IQS line) and benchtop variable attenuators are built for top performance and pinpoint accuracy. Each model offers a distinct set of features and specifications to suit various testing needs.
-
product
Immunity Testing Systems
CIS Series
The CIS series test systems are configured to perform conducted immunity testing according to IEC 61000-4-6. The system includes an ACS series power amplifier, coupling/decoupling Network (CDN), directional coupler, 150Ω to 50Ω adapters, power attenuators, cables and [optional] CSAT software. These systems, when properly configured, are capable of testing your products to all levels given in IEC 61000-4-6 up to 230 MHz. You can choose from three systems. Follow the links below for detailed information, including a comprehensive datasheet listing system specs.
