Filter Results By:
Products
Applications
Manufacturers
- Baraldi S.r.l.
product
DUMMY BLOCK
STAG 10
Ideal requirements of release agent between billet and dummy block:Optimal adhesion to the substrate, Optimal anti-soldering power, No hazardous fumes/vapors development during use, Non-flammable at the effective temperature, No build-up, no interferences on run out table.
-
product
Corona Treaters
Electro-Technic Products, Inc.
Electro-Technic's surface treaters include a handheld model (BD-20AC) and a production line model (BD-80C). Our handheld model (BD-20AC) is suited for a manual operator to treat small surfaces to increase bonding or adhesion in lab/test environments. Customers looking for a production-scale corona treater can opt for our BD-80 model which features continous operation and can be customized to come with a conveyer belt and a mounting stand.
-
product
Adhesion Testers
From the largest man-made structures to the smallest household appliances, most manufactured products have a protective or cosmetic coating. Premature failure of this coating can, at the very least, result in additional costs of rework. Adhesion testing after the coating process will quantify the strength of the bond between substrate and coating, or between different coating layers or the cohesive strength of some substrates. Routine adhesion tests are used as part of inspection and maintenance procedures to help detect potential coating failures.
-
product
Fretting Tester
FFT Series
Fretting wear is a test where surface damage occurs between two contacting surfaces experiencing oscillatory displacement of small amplitude. At the contact point, lubricant/coating is squeezed out or the low amplitude motion does not permit the contact area to be re lubricated/ debris dislodge resulting in serious local wear occurs. This type of wear causes two-body abrasion, adhesion and/or fretting fatigue wear.
-
product
Surface Profile
Surface profile: The degree of profile on the surface affects a coating’s overall performance and determines aspects such as adhesion, coverage and overall volume of coatings used. If the profile is too large the amount of coating required increases, otherwise there is a danger that the peaks remain uncoated - allowing rust spots to occur. If the profile is too small there may be an insufficient key for adequate adhesion.
-
product
Material Test Machines
Sanwood Environmental Chambers Co ., Ltd.
Sanwood Universal Test Machines, UTM, are widely use for different material testing, like semi-product & finished product made of rubber, plastic, metal, nylon, non-woven fabrics, textile, tape, polyfoam, waterproof materials, wire, cable, etc. With different test jigs or fixtures, the UTM can run the tensile, compression, shearing foce, adhesion, peeling force, tear strength, fatigue, etc test according to GB, CNS, ASTM, ISO, DIN, JIS, EN test standards.
-
product
Cross Cut Adhesion Tester
1540
The Elcometer 1540 Cross Cut Adhesion Tester is a simple instrument for quickly determining the coating adhesion of a large variety of paints up to 50µm (2 mils) thickness.
-
product
Initial Adhesion Tester
CZY-G
CZY-G Initial Adhesion Tester is suitable for pressure-sensitive tapes, medical patches, self-adhesive labels, protective films and other related products for initial tack testing.
-
product
Cylindrical Mandrel on a Stand
1500
The Elcometer 1500 Cylindrical Mandrel on a stand is a simple instrument for determining the elasticity, adhesion and cracking of dry paint on flat specimens, consisting of mandrel support which also serves as a test stand.
-
product
Standard & Top Paint Inspection Gauges
121/4
The Paint Inspection Gauge Top model has an internal carousel allowing each of the three cutters to be selected easily together with a cross hatch adhesion tester.Compact and convenient, ideal for paint thickness measurement in confined areasMade of anodised aluminium for durabilityBright LED light source for clear visionTop Model can hold one cross hatch cutter & three standard cutters which are locked tight, a simple rotation of the cutter holder changes the cutting tool.
-
product
Coating And Finish Durability
Our Capabilities*Adhesion*Impact Resistance*Gravelometer*Chemical Resistance*Cyclic Corrosion*Hardness*Chipping Resistance*Water Immersion
-
product
Jerking Tester
JLD-10
Shanghai Dean Electrical Co., Ltd
Executive standard: GB/T4074.3-2008/IEC60851-3; Inspection standard:JB/T4279.5-2008Used to measure the film adhesion property of enameled round wires with nominal conductor diameter of 1.000mm and below;Built-in small ultra-quiet air compressor would provide power supply and automatic constant pressure;Samples, while being jerked, would not move and slip out;
-
product
Plastic Testing Machines
Infinity Machine International Inc.
Plastic Testing Machines by Infinity Machine International Inc. - for applications such as constant temp adhesion tester, plastic testing equipment heating distortion resistance testing, adhesive tape holding power test machine, plastic impact resistance, impact resistance for plastic pipes, salt spray plastic testing machines, uv accelerated weather plastic testers, and more.
-
product
Pull-Off Adhesion Tester
506
The Elcometer 506 are lightweight, portable and easy-to-use adhesion testers available in analogue or digital gauges and are suitable for measuring the pull-off adhesion of coatings up to 50MPa (7250psi) either on-site, or in the laboratory.
-
product
Surface Profile
Surface profile: The degree of profile on the surface affects a coating’s overall performance and determines aspects such as adhesion, coverage and overall volume of coatings used. If the profile is too large the amount of coating required increases, otherwise there is a danger that the peaks remain uncoated - allowing rust spots to occur. If the profile is too small there may be an insufficient key for adequate adhesion.
-
product
Push Off Adhesion Tester
508
Hand-held, ergonomic and fully portable - ideal for on-site adhesion testingQuick connect coupling for easy connection to the dollyMeasurement range up to 25MPa (3630psi) with a full scale accuracy of ±1.5%Rotating crank handle applies smooth loading from 0 up to 25MPa (3630psi)
-
product
Adhesive Tack Testers
Adhesion test is to measure the initial tack and holding power of adhesive tapes and labels. Tack or holding power test is very important in packaging industry and adhesive industry.
-
product
Scratch Tester
Scratch testers from Anton Paar are used to characterize film-substrate systems and to quantify parameters such as adhesive strength and friction force by using a variety of complementary methods. This makes scratch testers invaluable tools for the determination of coating adhesion, scratch resistance, and mar resistance in research, development, and quality control.
-
product
Cross Hatch Adhesion Tester
1542
The Elcometer 1542 Cross Hatch Adhesion Tester is ideal for measuring the cross hatch adhesion of coatings up to 250µm (9.8mils) on flat surfaces and test panels.
-
product
Adhesion testing
Adhesion is the tendency of dissimilar particles and/or surfaces to cling to one another. The adhesive strength of paint and coatings are of crucial importance to enable the material to meet the basic functions of protection and decoration. Cross-Cut or Cross Hatch Test, Scrape Adhesion, Pull-Off Test.
-
product
Pull Off Adhesion Tester
106
Applications for the Elcometer 106 Adhesion Test include paint or plasma spray on bridge decking, coatings on steel, aluminium, concrete etc.Supplied in a carry case - ideal for site testsHand operated - no need for a power supplyIncludes a cutter for EN13144 and ISO 4624 tests
-
product
Adhesion Testers
The Cross Hatch Cutter is for assessing the resistance of paint coatings to separation from substrates when a right angled lattice pattern is cut into the coating, penetrating through to the substrate, it can also be viewed for adhesion between coating layers.
-
product
Hydraulic Adhesion Testers
108
The Elcometer 108 adhesion tester is the ideal gauge for testing coatings on tanks, pipelines, etc.Hand-Powered and portable adhesion testerIdeal for site workReusable stainless steel dolliesElcometer Digital Adhesion Tester features:Maximum hold - displays the highest value reachedBacklit display for dark areasRubber protective casingSwitchable Metric/Imperial units.
-
product
Conformal Coating Inspection (CI AOI)
They cover the components, the area around the components and identify most coating issues including cracks, bubbles, insufficient / excess coating, loss of adhesion and other common contaminations. Full coverage inspection for conformal coating.
-
product
Adhesion Tester
Surf-2
Rtec Adhesion Tester is a turn key solution to measure Pull up Adhesion force, Work of Adhesion and Shear Adhesion of materials. Equipped with Ultra-Sensitive Capacitance Load Cells this tester provides µN level resolution with forces up to 5N. The High-Resolution sensors allow characterization of large samples over macroscopic length scales to study the effect of texture and other surface modifications. Integrated with High Resolution Inverted Camera, it allows the researchers to measure Contact Area vs. Force making it extremely useful in measuring Adhesion of Soft Materials, Biomimetics and Hydrogels.
-
product
Pull tester with uplift kit and pulling plate
UPLIFT 2000
The Uplift portable tester was designed in conjunction with SPRI, for testing on the field the uplift resistance of adhesion. Easily test the attachment of the tile to underlayment and determine whether the uplift resistance performance meets the minimum wind load requirements.
-
product
Disk Peel Tester
DRK186
Shandong Drick Instruments Co., Ltd.
DRK186 Disk peel tester is applied to test the ink layer bonding strength of plastic film printing and PT print. To test the surface adhesion state of vacuum coating, surface coating, composite process.
-
product
Static Generation
Charging Electrodes
Fraser Anti-Static Techniques Ltd
Provide a safe, controllable, reliable and cost-effective method of applying static charge for temporary adhesion.
-
product
Peeling Tester
BN-3
Shanghai Dean Electrical Co., Ltd
Executive standard: GB/T4074.3-2008/IEC60851-3;Inspection standard: JB/T4279.6-2008Used to measure the film adhesion property of enameled round wires with nominal conductor diameter of 1.0mm and below;High-end SCM control is used;Set arbitrarily the number of twist;LED would automatically display the number of twists;Twist counter performs accurate and reliable counting;High-strength steel scraper would complete sample scarping at once, easy to operate and use.
-
product
Coatings Inspection Division
For over seventy years, Elcometer has been a world leader in the design, manufacture and supply of inspection equipment to the coatings industry. Whether you are measuring surface profile, surface cleanliness, dry film thickness, porosity, adhesion or gloss; or testing the abrasion, scratch resistance or elasticity of a coating - Elcometer's extensive and versatile range of equipment provides the complete solution to your coatings inspection requirements, whatever and wherever they might be.
-
product
Roughness Testers
Roughness is an important parameter when trying to find out whether a surface is suitable for a certain purpose. Rough surfaces often wear out more quickly than smoother surfaces. Rougher surfaces are normally more vulnerable to corrosion and cracks, but they can also aid in adhesion. A roughness tester is used to quickly and accurately determine the surface texture or surface roughness of a material. A roughness tester shows the measured roughness depth (Rz) as well as the mean roughness value (Ra) in micrometers or microns (µm). Measuring the roughness of a surface involves applying a roughness filter. Different international standards and surface texture or surface finish specifications recommend the use of different roughness filters. For example, a Gaussian filter often is recommended in ISO standards.
