Filter Results By:
Products
Applications
Manufacturers
- Pickering Interfaces Inc.
product
Interface Board for Gigabit Ethernet
40-965-910
The 40-965-910 is a converter card for the 40-201 Ethernet/AFDX Fault Insertion Switch. Adapts the 78-Pin D-type connector on the front of the module to 4 RJ45 sockets and one 9-way D-type connector for fault signals. Allows the fault insertion testing of Gigabit Ethernet signals.
-
product
Bit Error Rate Tester
100G NRZ BERT
The C-BERT 2810-4 is a complete bit error rate tester dedicated for 100G Ethernet applications. The four independent channels enable an actual operating environment with traffic on all lanes. The simultaneous testing of 4 channels is much faster than testing each channel individually saving time and money. The BERT eye scan reveals low-probability events and shows the true performance of the DUT to aid troubleshooting. The high RF port density eliminates long cable length which degrades the signal at 25 Gb/s. The OS independent GUI is easy to install and enable remote control from everywhere. The complete and compact C-BERT is a powerful and cost efficient test solution for 100G Ethernet.C-BERT MI-PE2810-4 Product sheet_rev05.
-
product
PXIe-8861, 2.8 GHz Quad-Core PXI Controller
787567-01
PXIe, 2.8 GHz Quad-Core PXI Controller - The PXIe‑8861 is an Intel Xeon 4‑Core embedded controller for PXI Express systems. You use it for processor-intensive RF, modular instrumentation, and data acquisition applications. The PXIe‑8861 includes two 10/100/1000BASE‑TX (Gigabit) Ethernet ports, two USB 3.0 ports, four USB 2.0 ports, as well as an integrated hard drive, serial port, two Thunderbolt™ 3 ports, and other peripheral I/O. Thunderbolt and the Thunderbolt logo are trademarks of Intel Corporation or its subsidiaries in the U.S. and/or other countries.
-
product
Passive Network TAPs
ApconTap
Our portfolio of passive optical network TAPs captures network traffic under all conditions to simplify network monitoring and security. Each ApconTap model supports common datacenter optical fiber standards with split ratio options availble at 50/50, 60/40, and 70/30. With passive fiber 40G and 100G TAPs, APCON offers short-range, long-range, and bidirectional models to accomodate requirements for high-density, next-generation datacenter deployments.
-
product
40-CH 100G Athermal AWG
Athermal AWG(AAWG) have equivalent performance to standard Thermal AWG(TAWG) but require no electrical power for stabilization. They can be used as direct replacements for Thin Film Filters(Filter type DWDM module) for cases where no power is available, also suitable for outdoor applications over -30 to +70 degree in access networks. Flyin’s Athermal AWG(AAWG) provide excellent optical performance, high reliability, ease of fiber handling and power saving solution in a compact package. Different input and output fibers, such as SM fibers, MM fibers and PM fiber can be selected to meet different applications. We can also offer different product packages, inluding special metal box and 19” 1U rackmount.
-
product
PXIe-8881, 3.9 GHz 8-Core PXI Controller
787805-01
PXIe, 3.9 GHz 8-Core PXI Controller - The PXIe-8881 is an Intel Xeon 8-Core embedded controller for PXI Express systems. You use the PXIe-8881 for processor-intensive RF, modular instrumentation, and data acquisition applications. The PXIe‑8881 includes two 10/100/1000BASE‑TX (Gigabit) Ethernet ports, two USB 3.0 ports, four USB 2.0 ports, as well as an integrated hard drive and other peripheral I/O, such as two Thunderbolt 3 ports. Thunderbolt is a trademark of Intel Corporation or its subsidiaries in the U.S. and/or other countries.
-
product
Tensile Strength Tester
Capacity of Tester with accuracy of 100g : 250 Kgf. and 500 Kgf.Capacity of Tester with accuracy of 10g : 20 Kgf, 50 Kgf and 100 KgfS Type Load Cell fixed with Top GripTraverse Speed: 300 & 100mm /min.Grip Separation: 1000 mmGrip Separation: 25 mmTop Grip is fixed and Bottom Grip is Movable Type.Elongation measurement by Steel Scale and Digital Counter Meter Both.Digital Display of Load and Elongation.Peak value of last test can be read.User friendly key panel with switch of zero setting and peak value of last testMotor: 1/2 HP single phase 220V 50 Hz. ( for Capacity up to 100 Kgf )Motor: 1 HP single phase 220 V 50 Hz ( for Capacity up to 500 Kgf)Power: 220 V AC 50 Hz.Safety device by limit switch to protect from over traverse.
-
product
2-Port 10/100/1000 Base-T Ethernet NIC, Intel® 82580DB, PCIe I/F to processor
EM1
The EM1 module integrates the Intel® 82580 GbE Controller with supporting magnetics and circuitry to provide dual-port gigabit (10/100/1000Base-T) Ethernet network controller functions. NAI Single Board Computer (SBC) boards are typically designed with dual-port NICs. The EM1, with direct-connect PCIe interface, allows for seamless SBC/processor configuration providing access to additional Ethernet communication port functions.
-
product
Dual-Port 100G PCIe Ethernet NIC
P2100G
The P2100G 2x100G PCIe NIC builds upon the success of the widely deployed NetXtreme E-Series architecture by combining a high-bandwidth Ethernet controller with a unique set of highly optimized hardware acceleration engines to enhance network performance and improve server efficiency.
-
product
PXIe-8861, 2.8 GHz Quad-Core PXI Controller
785831-33
PXIe, 2.8 GHz Quad-Core PXI Controller - The PXIe‑8861 is an Intel Xeon 4‑Core embedded controller for PXI Express systems. You use it for processor-intensive RF, modular instrumentation, and data acquisition applications. The PXIe‑8861 includes two 10/100/1000BASE‑TX (Gigabit) Ethernet ports, two USB 3.0 ports, four USB 2.0 ports, as well as an integrated hard drive, serial port, two Thunderbolt™ 3 ports, and other peripheral I/O. Thunderbolt and the Thunderbolt logo are trademarks of Intel Corporation or its subsidiaries in the U.S. and/or other countries.
-
product
Fanless Embedded System With 7th Gen Intel® Core™ I7/i5/i3 & Celeron® Processors, Built-in Layer 2 Managed PoE Switch For Railway PC
tBOX400-510-FL
The tBOX400-510-FL is a two-in-one transportation-certified box PC with built-in layer 2 managed PoE switch for IP surveillance applications. The tBOX400-510-FL is certified with CE (Class A) and FCC and is in compliance with EN 50155 and EN 45545-2. This high-performance transportation box PC is powered by the 7th generation Intel® Core™ (Kaby Lake) or Intel® Celeron® 3965U processors, along with dual DDR4 SO-DIMM slots for up to 32GB of memory. The built-in 10-port managed switch is powered by Qualcomm's chip. The tBOX400-510-FL has a built-in 10-port managed switch with 8-port 10/100 Mbps PoE and 2-port Gigabit LANs, featuring VLAN, QoS and PoE scheduling for the more secure and smooth network. For reliable operation in severe environments, the rugged fanless transportation box computer is designed to withstand a wide temperature range from -40°C to +60°C and vibration of up to 3 Grms. It also supports a wide voltage input range: 9V to 36V DC for vehicle applications, 14V to 32V DC for marine applications, and 24V to 110V DC for railway applications. With its high performance, industrial-grade design and full-strict certifications, the tBOX400-510-FL is suited for transportation-related applications such as onboard video surveillance and video management.
-
product
Ethernet Switch and Router
VPX6-684
Curtiss-Wright Defense Solutions
Curtiss-Wright's VPX6-684 FireBlade provides Systems Integrators with a fast, secure and unified approach to interconnect subsystems, chassis, cards, and compute nodes within any given platform using 1 or 10 Gigabit Ethernet links. Providing up to 24 wirespeed 10/100/1000 Mbps interfaces and up to four 10 Gbps interfaces in a single 6U VPX slot, the VPX6-684 Ethernet Switch is ideal for architecting system-wide Intra-Platform Networks (IPNs).
-
product
Data Center
InnoLight Technology Corporation
New applications such as digital reality, artificial intelligence, machine learning are driving the network traffic to an unprecedented level. Cloud operators need continuing innovation in optical solutions to support bandwidth demand. InnoLight's comprehensive family of optical transceivers, including 10G, 25G, 40G, 100G, 200G, 400G and 800G will enable cloud operators to rapidly upgrade its network.
-
product
Network Emulator
Netropy® 100G
Developed for the pre-deployment testing and validation of high-speed 100GbE networks, the 100G is capable of precisely emulating 25, 40, 50 and 100Gbps WAN links. It allows service providers and storage system manufacturers to validate how WAN impairments--such as latency, packet loss or congestion--will affect performance over all data center links prior to going to market. Available 1/18
-
product
ATCA Rugged Blade Processor With Dual Xeon Cascade Lake-SP, 100G Ethernet
ATC129
The ATC129 is a high performance ATCA processor blade featuring dual 24 core Intel® Xeon® processors, each with six banks of memory providing up to a total of 384 GB DDR4 memory with ECC.
-
product
Optical Clock-Recovery Modules / O-CR
Optical clock-recovery modules are required when a clock signal is not present to trigger the oscilloscope or when it is better to use the embedded clock present in the data stream, such as for 100G Lambda optical signals.Clock-recovery modules are essential for transmitter signal characterization.
-
product
PXIe-8880, 2.3 GHz Eight-Core PXI Controller
783513-05
PXIe, 2.3 GHz Eight-Core PXI Controller—The PXIe‑8880 is an Intel Xeon 8‑Core embedded controller for PXI Express systems. You use it for processor-intensive RF, modular instrumentation, and data acquisition applications. The PXIe‑8880 includes two 10/100/1000BASE‑TX (Gigabit) Ethernet ports, two USB 3.0 ports, four USB 2.0 ports, as well as an integrated hard drive and other peripheral I/O.
-
product
Optical tTansceiver Module
QSFP28
Eoptolink Technology Inc., Ltd.
Eoptolink’s EOLQ-851HG-02 QSFP28 SR4 100G Optical transceiver module are designed for use in 100 Gigabit Ethernet links over multimode fiber. They are compliant with the QSFP28 MSA and IEEE 802.3bm 100GBASE-SR4 and CAUI-4. Digital diagnostics functions are available via the I2C interface, as specified by the QSFP28 MSA.
-
product
Shock0 to 100g
TGP-0610
The shock logger TGP-0610 measures impacts and can be used for machine condition monitoring and the monitoring of expensive and/or fragile shipments.
-
product
Dense Wavelength Division Multiplexer Mux & Demux Module 8 Channels 100G with LC/PC Connector
GLSUN-DWDM
Guilin GLsun Science and Tech Group Co., LTD
Wavelength ITU channels 186.6 to 196.1 THz Return Loss ≥ 45 dBDirectivity ≥ 50 dB Connector LC/PCMax. Optical Power ≤ 500 mW PDL ≤ 0.15 dBRelative Humidity 5%~ 95% Dimension 100×80×10.5 mmOperating Temperature -10℃ to +70℃ Storage Temperature -40℃ to +85℃
-
product
100G,200G 1X2 DWDM Device (3Ports)
Flyin optronics’ 100GHz/200GHz 1x2 wavelength multiplexer utilizes thin film coating technology and proprietary design of non-flux metal bonding micro optics packaging to achieve optical add or drop at a ITU wavelength. It provides ITU channel center wavelength, low insertion loss, high channel isolation, wide pass band, low temperature sensitivity and epoxy free optical path . It can be used for wavelength add/drop in telecommunication network system.
-
product
PXIe-8880, 2.3 GHz Eight-Core PXI Controller
783513-04
PXIe, 2.3 GHz Eight-Core PXI Controller—The PXIe‑8880 is an Intel Xeon 8‑Core embedded controller for PXI Express systems. You use it for processor-intensive RF, modular instrumentation, and data acquisition applications. The PXIe‑8880 includes two 10/100/1000BASE‑TX (Gigabit) Ethernet ports, two USB 3.0 ports, four USB 2.0 ports, as well as an integrated hard drive and other peripheral I/O.
-
product
PXIe-8881, 3.9 GHz 8-Core PXI Controller
786636-01
PXIe, 3.9 GHz 8-Core PXI Controller - The PXIe-8881 is an Intel Xeon 8-Core embedded controller for PXI Express systems. You use the PXIe-8881 for processor-intensive RF, modular instrumentation, and data acquisition applications. The PXIe‑8881 includes two 10/100/1000BASE‑TX (Gigabit) Ethernet ports, two USB 3.0 ports, four USB 2.0 ports, as well as an integrated hard drive and other peripheral I/O, such as two Thunderbolt 3 ports. Thunderbolt is a trademark of Intel Corporation or its subsidiaries in the U.S. and/or other countries.
-
product
Communication Test Set
Eye-BERT 100G
The Eye-BERT 100G is a low cost, full-featured, stand-alone communication test set with an integrated post equalizer eye opening monitor / scanner. Ultimate flexibility is provided with three different physical interfaces, 13 different configurations, and configurable transmit and receive clocks. The tester supports PRBS patterns up to 263-1 and select data rates from 1.25 to 29Gbps on up to 4 simultaneous channels. Front panel controls are also provided for stand-alone operation. Unlike competing products, fast post equalizer eye monitoring and scanning is included and can be performed on any input channel above 5Gbps.
-
product
100G,200G DWDM OADM Module (4,8-Channel)
Flyin Optronics 100GHz/200GHz wavelength multiplexer(100,200G DWDM OADM Module) utilizes thin film coating technology and proprietary design of non-flux metal bonding micro optics packaging to achieve optical add or drop at a ITU wavelength. It provides ITU channel center wavelength, low insertion loss, high channel isolation, wide pass band, low temperature sensitivity and epoxy free optical path . It can be used for wavelength add/drop in telecommunication network system.
-
product
Lightweight Sensor
FT205
The FT205 delivers high performance in a light package. Made from a graphite and nylon composite, and weighing only 100g (3.5oz), this sensor has been specifically designed for use on drones and unmanned aerial vehicles (UAV).
-
product
Fiber Optic Qualification & Dispersion Test Links
8800 Family
Delaire USA qualification test systems are designed to act as worst-case links for bandwidth/dispersion and attenuation, or to meet the customer's loss, dispersion, and distance requirements for custom applications. Because the test links are constructed from hand-selected, industry-standard fiber and not simulated with dispersion elements, all of the effects including loss, dispersion, and fiber nonlinearities are present and authentic. Typical applications include optical transciever testing and qualification for 40G AND 100G systems
-
product
Fiber Optic Connectors
TE's fiber optic connectors accommodate 10G Ethernet — with the capacity to handle next-generation 40G and 100G when needed — without the severe distance limitations of copper cable. Easy to maintain in the field, and reliable when operating in harsh environments, our fiber optic cable connectors offer significant size and weight savings. Our broad portfolio includes several fiber optic connector types including standard fiber connectors, LC connectors and SC connectors.
-
product
Integrated Optical Modulation Analyzer
N4392A
The new Keysight N4392A is an ultra-compact, portable fully integrated optical modulation analyzer with a 15'' laptop-size screen. It is optimized for daily R&D work and designed for the most affordable performance verification in manufacturing and component test for 40/100G components, modules and systems. It is the first optical modulation analyzer that provides built-in performance verification and recalibration, extending the factory recalibration cycles significantly.
-
product
50/100G PAM4 Pin Photodiodes
Macom Technology Solutions Holdings Inc.
MACOM offers high sensitivity PIN photodiodes with industry leading performance at speeds of 56Gbd / 100G. Proprietary designs enable operation using PAM4 modulation protocols in 50 /100G applications. The high responsivity designs have high reliability and are suitable for use in both tele-communications and datacenter networks. The high bandwidth PIN photodetectors are available in a back illuminated design (highest performance), a front illuminated design (more cost effective) and in both singlet and array form factors
-
product
1.6T Optical Receiver Test Application
N4917DJCA
Offers fully automated stress eye calibration and receiver testing for 800G and 1.6T modules with 100G and 200G / λ optical interfaces.
