Applied Test Resources
Applied Test Resources (ATR) was established in 1997, with the primary objective of providing advanced Analog Test software solutions for the semiconductor Industry. As ATR's business developed, we saw an increasing need in the industry for cost effective, user-friendly, specific advanced analog test hardware. ATR then redirected our focus to develop total test solutions at highly competitive prices. Our product to meet the demand for customized test solutions at lower test costs is the MTS-2010 Mixed Signal Test System.
- (610) 488-0802
- sales@atr-inc.org
- 3219 E. Camelback Rd.
Suite 201
Phoenix, AZ 85018
United States
-
product
High Speed Matrix Card
MATX4001
The MATX4001 module is a general purpose-switching matrix, consisting of 40 relays arranged in 5 rows by 8 columns. Each row/column consists of independent Force/Sense lines that are switched simultaneously. Each relay is capable of handling 1 Amp and can isolate up to 5 KV. Each relay on the matrix is independently controlled with an On/Off command via software
-
product
Mixed Signal Test Systems
MTS1000i
The MTS-1000i is lowest cost platform available in the MTS series of ATE. It has a reduced platform size compared to the MTS-2010i & MTS-1020i, reduced power supplies, and 4 slots. It is mainly intended for single site testing. Like the other testers in the MTS family it is a highly cost effective production ATE designed for testing high-volume linear and mixed signal semiconductor devices (Op Amps, high-voltage drivers, DAC, ADC, etc.), both at the wafer sort and final test stages of the manufacturing process
-
product
High Voltage Power Source
PM1000
The PM1000 is a high voltage power source capable of supplying up to 1000 V/20 mA to a load. It is intended for use in measuring leakage and breakdown voltages of devices. There are five voltage ranges and five current ranges.
-
product
Mixed Signal Test Systems
MTS2010i
The MTS-2010i are a cost effective production ATE designed for testing high-volume linear and mixed signal semiconductor devices (Op Amps, high-voltage drivers, DAC, ADC, etc.), both at the wafer sort and final test stages of the manufacturing process.
-
product
Four Quadrant Power Source
PM2010
The PM2010 is a four-quadrant power source capable of supplying up to 20 V/10 Amps to a load. The maximum power that may be safely generated is 50 Watts on a continuous basis and 200 Watts peak on a pulsed mode for no more than 100 ms, and a duty cycle of less than 10%
-
product
DUT Prototype Board
DPB8800
The DPB8800 is an 11? x 14? PC board used to interface the tester with the Device Under Test (DUT). This board contains generous area for custom circuitry and extra relays. The DPB8800 is also available with standard solutions to test families of components like Op-Amps, Regulators, ADC?s and DAC?s. +/-15 V and +5 V are available to support circuitry biasing.
-
product
Mixed Signal Test Systems
MTS1010i
The MTS-1010i is a more economical version of the MTS-2010i & MTS-1020i testers. It has a reduced platform size and reduced power supplies. Like the other testers in the MTS family it is a highly cost effective production ATE designed for testing high-volume linear and mixed signal semiconductor devices (Op Amps, high-voltage drivers, DAC, ADC, etc.), both at the wafer sort and final test stages of the manufacturing process.
-
product
16 Bit Digital Card
DB1600
The DB1600 is an inexpensive digital card that provides basic digital control capability without some of the more sophisticated features available on the DRM1650. The DB1600 allows for the control of 16 bits of data. The logic levels may be programmed anywhere within the range of 12 V.
-
product
Floating Power FET moduleAmp Loop
PFM1010
The PFM1010 Module is a precision instrument capable of measuring all common DC parameters in a power MosFet as well as many of the AC parameters. This module uses some very innovative techniques to make it possible to measure parameters like Rdson down into the sub-million-ohm range.
-
product
Floating 6-Ch Integrated Power Source
PM0650
The pulse channels provide voltage pulses with duration control 10us to 100ms, and measures current. The combination of capabilities provides a versatile solution on fulfilling the wide range of requirements on testing a device. The PM0650 may be floated up to ±1500V to facilitate HV isolation test of devices where outputs may be connected directly to line voltages.
-
product
Multiple (8) Four Quadrant High Power Source
PM0830
The PM0830 consists of eight fully independent four-quadrant power sources. Two of the channels are capable of supplying up to 30 V/500 mA each. The remaining six channels are capable of supplying up to 30 V/50 mA each. The PM0830 has a measurement range capable of measuring voltages up to 1000V.
-
product
High Voltage Power Source
PM2000
The PM2000 is a high voltage power source capable of supplying up to 2000 V and sourcing 10mA to a load. The high potential at 2 kV fulfills coverage for mostly all semiconductor devices where leakage and breakdown measurements are involved. The module has been incorporated with interlock feature to ensure safety.
-
product
Quad Op-Amp Loop
QOAL400
The QOAL400 module is a precision instrument capable of measuring all common parameters of an Op Amp, including AC as well as DC parameters. The QOAL400 has four completely independent channels, which allow a quad device to be tested in a minimum amount of time. Each channel has a full set of resources to measure all common parameters.
-
product
Multiple (8) Four Quadrant Power Source
PM0820
The PM0820 uses an onboard controller, which relieves the system CPU of performing many functions necessary for the module operation. The result is higher efficiency of the CPU and faster execution of the module commands.
-
product
Matrix Card
MATX4010
The MATX4010 module is a general purpose-switching matrix, consisting of 40 relays arranged in 5 rows by 8 columns. Each row/column consists of independent Force/Sense lines that are switched simultaneously. Each relay is capable of handling 10 Amps and can isolate up to 5 KV. Each relay on the matrix is independently controlled with an On/Off command via software.
